Categories: Auto Repair

Benz W176 B177655 LED Daylight Trobule Repair by Launch X431

After replacing headlight for Benz A-class W176,the LED daylight will not working correctly.And if you scan DTC in the system,the trouble code B177655 will be found.So this instruction show you the procedures on how to use Launch X431 PAD V to solve it.

More information for Benz trouble repair,please refer to Mercedes Benz Trouble Repair.

B177655:Control unit “Actuation module,LED exterior lighting,left front” has a malfunction.The component is not configured.

 

Preparations:

Launch X431 PAD V/X431 PAD VII or X431 IMMO PAD

 

Procedures:

Connect Launch X431 PAD V to Benz car,then access Benz menu to make a full health report and check all DTC.

 

Select “SG-SW-HEADLAMPS”–>”Read Trouble Code”

Back to “SG-SW-HEADLAMPS” menu to select “Special Function”–>”Teach-in Processes”

Select “Commissioning of control unit “E1n7(Actuation Module,LED exterior lighting,left front)”

In the following sequence,the string of characters must be localized on the lamp unit for teaching in control unit “E1n7 (Actuation module,LED exterior lighting,left front)”.The string of characters must hen be entered into the diagnostic unit.

 

If the string of characters on the headlamp is recognized as faulty and is not accepted, please contact the User Help Desk. It is not permissible to enter another string of characters without being prompted to do so e.g. that of another headlamp. The headlamp can be(irreparably) damaged by an incorrect string of characters.

Click “Continue”

Commissioning of control unit “E1n7(Actuation module, LED exterior lighting, left front)”

Enter the string(without spaces or hyphens and in lowercase letters) with label”LAM-S-3K”into the following field. Press button

“Continue”to continue.

LAM-S-3K Enter string:******

The following requirements must be satisfied so that the string is clearly visible:

-The engine hood is open.-The headlamp is removed.

-The control unit “E1n7(Actuation module, LED exterior lighting, left front)”was removed.

-The string is located on the label inside the headlamp.

-The string must be 11 digits long.

-For example:1A 0017 5010AAIA8I

-The correct input of the string is:”a007500aaa8”.

Click “Input”

Input string of headlight control unit

Then press “Continue” and wait processing

After finishing,press “Continue”

Now back to menu to clear fault code,then read fault code again,you will find all work correctly.

More test report about Launch X431 please check:Launch X431 Test Report

auto

Recent Posts

Hitachi EX5600-7B Folding Stairway and Surrounding Parts Removal Guide

This instruction show you guide on how to remove folding stairway and surrounding part for…

8 hours ago

Jungheinrich Junior AME13 Spring-Loaded Brake Electrical Connection Removal Guide

It is necessary step to remove electrical connection cable before you do disassemble or some…

2 days ago

How to Use Nexiq eTechnician Function Test?

Nexiq eTechnician provides a number of special tests to assist you with your vehicle diagnostic…

4 days ago

JCB JS140 Excavator P0523-68 Engine Oil Pressure Low Solution

Here car-auto-repair.com show you guide on how to repair JCB JS140 excavator P0523-68 trouble code…

5 days ago

Volvo Version 3 and 4 Truck Oil Pressure Test by Volvo Techtool

Here is the instruction show you guide on how to use Volvo TECHTOOL and VOCOM adapter to…

7 days ago

How to Solve Allison 3000 & 4000 Gen5 P071A Neutral at Stop Input Failed ON

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 transmission…

1 week ago