Categories: How To

Benz Xentry DoIP Connection Windows Firewall Setting Guide

Here is a instruction show you guide on how to configure the Windows Firewall for Benz Xentry DoIP connection.

 

Related Conetetns:

2024.03 Benz Xentry.OpenShell.XDOS Diagnostic Software Free Download

How to Install Benz Xentry 2024.03 Diagnostic Software

 

 

To ensure a smooth data exchange between a DoIP compatible vehicle and the Open Shell diagnosis system, you need to unlock the Windows Firewall for specific additional communication ports.

In order to configure the Windows Firewall, please open the control panel and then click on entry
“Windows Firewall”. Please select entry “Advanced settings” in the menu bar on the left:

 

The Firewall must be configured for both inbound and outbound TCP/ UDP connections and therefore,specific ports must be unlocked entirely. Hence, you require a total of four Firewall rules.

 

Please proceed as follows:

Please select entry “Inbound rules”.

First an inbound TCP rule is set up.
Please ensure you are in step “Type of rule” (left). Please select option “Port” on the right. Then please click “Next”.

In the following step, please select option “TCP” and below option “Specific local ports”.
Please insert the following port numbers into the field, separated by comma:
13400, 13401, 13402, 13403

After clicking on “Next”, you will be directed to the information required for this action. There,
please select option “Allow connection” and confirm this by clicking “Next”.

In the following step “Profile”,please select all the options.

Please assign a name as well as an optional description and save the Firewall rule by clicking “Finish”.

Inbound TCP rule:
Please repeat steps 1 to 6, whereupon in step 3, you need to select option “TCP” instead of
“UDP”.
Then please insert the following port numbers under “Specific local ports”, separated by comma, just as you did for the previous inbound UDP rule (please note that these ports do not differ for inbound and outbound connections, in contrary to ports for SDconnect):
13400, 13401, 13402, 13403

Outbound TCP rule:
Please repeat steps 1 to 6, whereupon in step 1, you need to select “Outbound rules”.

Please insert the same information as mentioned above.

Outbound UDP rule:
Please repeat steps 1 to 6, whereupon in step 1″Outbound rules” as well as in step 3, you need
to select option “UDP” once more. Please insert all other data as before.
As soon as the IP address and Windows Firewall configuration is complete, your Open Shell System is ready for DoIP.

auto

Recent Posts

JCB JS140/205/215 Excavator C1022-13 Coolant Temperature Sensor Open Circuit

This instruction show you guide on how to solve JCB JS140/205/215 excavator C1022-13 trouble code coolant…

2 days ago

How to Diagnostic and Repair PCC1302 PowerCommand Code 2972 – Field Overload

If the time that the Field AVR Duty Cycle is operating at maximum output is…

3 days ago

Caterpillar C9 Engine 15 164-3 Injection Actuation Pressure Voltage High

The Engine Control Module(ECM) detects the following conditions: The voltage for the injection actuation pressure…

4 days ago

Volvo and Mack EPA 10 Engine Hydrocarbon Dosing Control Valve Test by JPRO

This instruction show you guide on how to perform hydrocarbon dosing control valve test for…

1 week ago

Fendt Tractor SPN 100 FMI 31 Oil Pressure Sensor Defect Solution

This instruction show you guide on how to solve Fendt tractor SPN 100 FMI 31…

1 week ago

Detroit GHG17 Heavy Duty Engine Piston Protrusion Measurement Procedure

Detroit GHG17 Heavy Duty Engine Piston Protrusion Measurement Procedure   Related Contents: 2024.06 Detroit Diesel…

2 weeks ago