Categories: Auto Coding

BMW E39 EWS & CAS Module Coding by NCS Expert

In this instruction,i will show you guide on how to use NCS Expert to perform EWS & CAS coding for BMW E39.And for more NCS Expert cases,please check here:NCS Expert projects

 

Preparations:

NCS Expert BMW Coding Software Download

NCS Expert program and coding guide

 

Procedures:

1.When you run NCS Expert you will see the next screen. Select “file – load profile”

2.In next screen you must select “code control unit. allow ZCS reading” : (it means that you will able to read coding from any ECU for selected chassis and than write this readed coding to all other

ECU for selected chassis)

3.In the next screen you will see: (the CHASSIS FG FA (it the coding data) now is empty) And now we need to enter this data. In this screen please select (F1) VIN/ZCS/FA

4.In the next screen you will see the same picture: (the CHASSIS FG FA (it the coding data) now is empty). And now we need to enter this data. In this screen please select (F1) ZCS/FA f. ECU. It

means that we will read ZCS/FA data from (f.) ECU

5.In the next screen you will see the chassis choice because depend on chassis the different list of ECU from wich we able to read coding. (we select E39)

6.In the next screen NCS Expert propose us to select from wich ECU we want to read “Correct” coding data. In most cases such coding stored in EWS or IKE. But in you car is better to read it

from EWS if this ECU originally for your car. In any case we can read the data from proposed ECU in selected chassis. (You can try read from different ECU for comparison). In this screen we

select EWS

 

7.After ECU choosing and pressing OK the NCS Expert will read coding data from specified ECU and write it in the upper part of NCS Ecspert window. (in was blank before on step 4).

Now NCS Expert ready to write this coding data to all ECU available in chassis.

In the end of this step we press F6 “Back”

 

8.We will see the screen with readed coding in upper part.

In the middle part of window will be write “Ready to coded: “ABS,EWS,IKE,DSC, LSC etc ECU” (list ECU depend from chassis)

In the bottom part of window (button part) will be active buttons: F1, Program Car, ECU etc.

If we select “Program Car” the NCS will program all ECU available in this chassis and listed in middle part of screen with data readed before and writed in upper part of screen.

If we select “Program ECU” the NCS will propose us to select special ECU which we want to code.

After selection we must press “execute job” or “process car”

And coding will start.

auto

Recent Posts

Doosan Excavator P0408 Maximum EGR Rate Governor Deviation Error Solution

This instruction show you guide on how to solve Doosan excavator P0408 maximum EGR rate…

1 day ago

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

3 days ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

6 days ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

1 week ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

2 weeks ago

How to Solve Fendt 800 Vario S4 wayline Running Slow

If the vehicle is oscillating on the wayline or catches up the wayline very slowly…

3 weeks ago