Categories: Auto Repair

BMW F Chassis 2011 Bleeding ABS Brake Operation Guide (Video)

This article show the guide on how to program ABS brake bleeding operation method for BMW F Chassis 2011.More step by step detail operation instruction,pls watch the video guide at end of article.Hope it helps.

 

Here are some other topic about ABS bleeding:

VW Tiguan Bleeding ABS Brake Pump By X431

How To Bleeding ABS Brake System Correctly For Your Car

 

 

Procedures of BMW F chassis ABS brake exhaust gudie:

 

Connect Launch X431 diagnostic tool to the vehicle and enter the software menu,select BMW V49.30.Processing…please wait…

Note:The software can diagnose the elec,control system of BMW,include engine/chassis/body and other parts.The operation is the same as the original scan tool.

Then Select “Manually Select”

Select “5 series”

Select “5’-F10/F11/F18”

Select “Chassis”

Select “ABS(Anti-lock Braking System-DSC)”

Communicating,please wait….

The software show the ECU IDENTIFY

Please pay more attention to ECU IDENTIFY,select “Ok”

Then select “Sepecial Function”

Select “Brake Bleeding Procedure”

Then software will pop-up a prompt,the content show as below,pay attention to the prompt,select “OK”

“The brake bleeding procedure must be carried out following work on the brake system.Residual air from the secondary circuit in the DSC unit is extracted.This improves the conventional ventilation process using the bleeder unit”

Then follow guide on software operations

Preparation:

Connect the brake fluid replacement device and switch online(The fill pressure must not exceed 2 bar)

Completely fush bleed.

Then attach bleeder bottle to rear left bleeder valve.

In the preparation stage,pay more attention to the prompts,then select “OK”

Open bleeder valve at rear left wheel

The pre-bleeding routine for the rear-axle brake circuit is started in the next test step.

For this purpose,a person must sit in the vehicle and press the brake pedal at 3 second intervals.

This process takes approx. 15 seconds

Pre-bleeding routine for the rear-axle brake circuit.

Press the brake pedal as far as it will go every 3 seconds.

This process takes approx. 15 seconds

Communicating,please wait…

Pre-bleeding routine at rear-axile brake circuit completed successfuly.

Rear left bleeder screw remains open.

Press [OK] to continue service function

The bleeding routine for the rear left wheel is started in the next test step.

During the routine,press the brake pedal as for as it will go every 3 seconds.

The routine bake approx. 30 seconds.

Wait for corresponding message.

Brake fluid free of bubles must emerge at the end of the routine.

Select “OK”,the software show below prompts.

“Bleeding routine for the rear left wheel

Press the brake pedal as for as ti will go every 3 seconds.

This process takes approx. 30 seconds.”

Bleeding routine at rear left finished successfully.

Close rear left-hand bleeder screw once the brake fluid started to emerge without bubbles and foam.

Attach bleeder bottle to front left bleeder valve and open front left bleeder screw.

Press [OK] to continue service function.

The pre-bleeding routine for the front-axle brake circuit is started in the nex test step.

Select [OK]

Pre-bleeding routine for the front-axle brake circuit

Press the brake pedal as far as it will go every 3 seconds.

This process take approx. 15 seconds.

Select [OK]

Communicating ,please wait…

…..

Just follow the software to complete front left,front right,rear right ABS brake routine beelding…

 

 

Here is the BMW 5 series F chassis ABS bleeding video guide:

auto

Recent Posts

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

2 days ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

5 days ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

1 week ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

2 weeks ago

How to Solve Fendt 800 Vario S4 wayline Running Slow

If the vehicle is oscillating on the wayline or catches up the wayline very slowly…

2 weeks ago

How to Adjust Cruise Control Release Linkage for Kubota L3901 Excavator?

This is instruction show you guide on how to adjust cruise control release linkage for…

3 weeks ago