Categories: Truck Repair

Bobcat 3450 Utility Vehicle Fuel Injector Disassembly and Assembly Guide

This instruction show you guide on how to disassembly and assembly fuel injector for Bobcat 3450 utility vehicle.

 

Related Contents:

Bobcat 3450 Utility Vehicle Fuel Injector Removal and Installation Guide

2023 Bobcat Service Analyzer 91.15 91.05 Diagnostic Free Download

 

Procedures:

Fuel Injector Disassembly
NOTE: Never use a steel wire brush to clean fuel injectors. Damage to the nozzle and other
components is likely to result.
Clean carbon from used injectors using clean diesel fuel.
Hardened deposits or varnish can be cleaned using a brass wire brush.

Place the fuel injector in a soft-jawed vise with the nozzle pointing up.
Remove the nozzle case nut.
Carefully remove the injector from the vise.

Turn the injector over and remove the nozzle body, nozzle valve, valve stop spacer, nozzle spring seat, nozzle spring and shims.

Inspect the sealing surfaces (Item 2) between the valve stop spacer and nozzle body for nicks
or scratches. Check the contact area between the valve stop spacer and the nozzle valve (Item 1) for scoring or pitting. Use a magnifying glass to inspect.

Perform a nozzle valve slide test:
(a) Wash nozzle body and valve in clean diesel fuel.
(b) While holding the nozzle body vertical, pull the nozzle valve about 2/3 of the way out.
(c) Release the valve. It should fall smoothly to its seat by its own weight.
NOTE: Replace the fuel injector assembly if it fails any inspection or if an injector tester is not available.

 

Fuel Injector Assembly
Secure the injector in a soft-jawed vise with the nozzle end up.
Install the shims, nozzle spring, nozzle spring seat, valve stop spacer, nozzle valve and nozzle body.
Install the nozzle case nut. Tighten to 49 – 53 N•m (36 -39 ft-lb) torque.

Fuel Injector Nozzle Pressure – Checking
NOTE: Never use a steel wire brush to clean fuel injectors. Damage to the nozzle and other components is likely to result.
Thoroughly clean the fuel injector nozzle using clean diesel fuel and a brass wire brush.
Visually inspect the fuel injectors and nozzle protectors for deposits or damage. Clean, repair or replace as necessary.
NOTE:Test the fuel injector using an injection nozzle tester. Operate the tester following the information provided by the tester manufacturer. Use clean, filtered fuel or FIE calibration fluid for the test.

Using the correct adapter, connect a fuel injector to a nozzle tester. Aim the fuel injector into a suitable container to catch the fuel spray.

Pump the operating lever of the tester slowly, observing the pressure reading at the point where the fuel injector begins spraying fuel.
NOTE: Opening pressure of a new fuel injector will be approximately 0,5 MPa (5,0 bar) (72.5 psi)
higher than one that has been operated for 5 hours or longer.

Pump the operating lever slowly to hold the pressure steady at a point just below the opening pressure and hold that pressure for 5 seconds. Observe the injector to see that it is sealing properly and is not dripping. If fuel leaks from the return line fitting, check that the nozzle case nut is tight. Service or replace the injector if fuel continues to leak from either the return line fitting or nozzle.

Pump the operating lever more rapidly to repeatedly “pop” the injector and observe the spray pattern. The pattern should be a very fine uniform spray. If dripping or an uneven pattern is seen, service or replace the injector.

 

More repair topic for Bobcat,please refer to:Bobcat Excavator Repair

auto

Recent Posts

How to Solve Allison 3000 & 4000 Gen5 Engine Trouble Code P0703

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 engine…

2 days ago

How to Solve Fendt MT1149 Tractor SCR System Emptying Not Completed

Here is the illustration show you guide on how to solve Fendt MT1149 tractor SCR…

1 week ago

How to Set Play Between Timing Pinion Teeth for CLAAS AXION 920 Tractor?

Here is the instruction show you guide on how to set play between timing pinion…

1 week ago

Perkins 1106D Generation Injector Data Incorrect Test Guide

Perkins 1106D Generation Injector Data Incorrect Test Guide   Preparations: Perkins EST 2024A & 2023A…

1 week ago

How to Solve Deutz EMR3 Engine Error 16/108/APSCD Trouble

This instruction show you guide on how to solve Deutz EMR3 engine error 16/108/APSCD trouble…

2 weeks ago

Kubota L4701 High Pressure Relief Valve Pressure Checking

Here show guide on how to check high pressure relief valve pressure for Kubota L4701…

2 weeks ago