Categories: ECU Chip Tuning

Bosch EDC16U34 Flashed by FGTech Galletto via BDM

This article aim at how to use FGTech Galletto to flash VAG Bosch EDC16U34 via BDM function.Hope it is helpful!

 

Part 1:How to use FGTech Galletto with BDM Function.

Part 2:Flashing Bosch EDC16U34 with BDM

 

Preparation:

FGTech Galletto 4 Master

A laptop with XP/Win 7/Win 10

Install FGTech Galletto

 

How to use FGTech Galletto with BDM Function:

Open the software and then click “OK”

In the screen of vehicle,please choose BDM/JTAG and click ok

Choose connect button

When the software and ECU has communication,please choose “Read All”,then click “Read Ext Flash”–>”Read Eeprom”

Pay attention when the power adapter connect to the BDM cable,do not connect reversely,or the ECU will burned and damaged.

When you connect ECU BDM cable,please pay attention on the cable color,and should not make a mistake.

 

Flashing Bosch EDC16U34 with BDM

Step1: Install the V54 FGTech Galletto 4 Master Software.
Step2: Connect the V54 FGTech ECU tuning kit with computer, setup boot and BDM.

Step3: Find out the BDM pads showed on the picture bellow.

Step4: Carefully align with the BDM Port ECU programming spring adapter/probe drop and secure frame.

Step5: Make sure everything is connected correctly, as in your PDF file.

Step6: Run FGtech V54 software, accept the system notice.

Attention: Make sure you have 12V+ feeding FGTECH 4 master main device and the intermediate adapter.

 

Step7: Switch intermediate adapter to ON, the read LED indicator will flash

Step8: Click the Option list as the order: “Select Driver”=> “BMD-Jtag”=>”Connect”.

Step9: The system is building communication between V54 FGTech Galletto 4 Master and computer. If communication is well built, green bar will start loading and finally display ECU information.

Step10: Ready to read and write ECU. Choose “Read Eeprom”, follow the system prompts to read eeprom.
Step11: Then select “Write Eeprom”, follow the system prompts.

Step12: Turn the switch off when complete write eeprom.
Step13: After the programming finished, exit FgTech V54 software program.

auto

Recent Posts

JCB JS140/205/215 Excavator C1022-13 Coolant Temperature Sensor Open Circuit

This instruction show you guide on how to solve JCB JS140/205/215 excavator C1022-13 trouble code coolant…

18 hours ago

How to Diagnostic and Repair PCC1302 PowerCommand Code 2972 – Field Overload

If the time that the Field AVR Duty Cycle is operating at maximum output is…

2 days ago

Caterpillar C9 Engine 15 164-3 Injection Actuation Pressure Voltage High

The Engine Control Module(ECM) detects the following conditions: The voltage for the injection actuation pressure…

3 days ago

Volvo and Mack EPA 10 Engine Hydrocarbon Dosing Control Valve Test by JPRO

This instruction show you guide on how to perform hydrocarbon dosing control valve test for…

6 days ago

Fendt Tractor SPN 100 FMI 31 Oil Pressure Sensor Defect Solution

This instruction show you guide on how to solve Fendt tractor SPN 100 FMI 31…

1 week ago

Detroit GHG17 Heavy Duty Engine Piston Protrusion Measurement Procedure

Detroit GHG17 Heavy Duty Engine Piston Protrusion Measurement Procedure   Related Contents: 2024.06 Detroit Diesel…

1 week ago