Heavy Equipment Repair

CLAAS AXION 950 Tractor Timing Setting Guide

Here is the instruction show you guide on how to perform timing setting for CLAAS AXION 950 tractor.

 

Related Contents:

CLAAS CDS 7.5 Diagnostic Software 2021 2020 Free Download

CLAAS 4x CAN Diagnostic Interface

Claas WebTIC Offline Repair & Service 2024 2015 Free Download

 

 

Procedures:

Setting the timing

► Remove the electric starting motor.

► Fit the special tool (1).

Fitting the camshaft timing tool

► Remove the fan.

► Remove the thermostat casing.

► Turn the engine flywheel with the special tool so that it can be placed in the holes (1).

► Fit the special tool.

► Fit two bolts at (1).

Fitting the crankshaft timing tool

► Time the camshaft.

► Remove the exhaust pipe.

► Remove sensor “B231”.

Before working on the timing, mark the hole through which the two-slot mark can be seen (1) on the flywheel (two types of fitting) when the camshaft is timed.

► Scenario 1: it is visible through the hole on sensor “B231” (3).

► Scenario 2: it is visible through the hole under the flywheel bell housing (2).

To check scenario 2.

► Remove the stiffener panel.

Remove the transmission shaft.

The position of the mark and the timing tool must be the same when the timing is set. It represents the timing position of the flywheel.

► Fit the special tool into position on sensor “B231”; it should be slotted into the housing in the flywheel.

Fitting the timing tool for the sensor “B054” target

To time the target of sensor “B054”, the crankshaft and camshaft must be timed.

► Remove the access panel (1).

► Remove the engine panel (2).

► Remove the centrifuge oil vapour filter.

Remove sensor “B231”.

► Fit the special tool (2) in the housing on sensor “B054”.

The special tool must be positioned on the tooth marked by the arrow.

If the special tool is not positioned on the tooth marked by the arrow.

► Undo the mounting bolts (1).

► Move the target so that the marker (3) and the special tool n o  00 1143 536 0 are lined up.

► Tighten the mounting bolts (1).

Removing the timing setting tools

► Remove the three timing setting tools.

► Turn the engine twice using the special tool.

► Fit the crankshaft timing tool.

► Check that the timing tools for the sensor B054 target and the camshaft can be easily fitted.

► Fit the centrifuge oil vapour filter.

► Fit the engine panel (2).

► Fit the access panel (1).

► Fit the sensor “B231”

► Fit the sensor “B054”.

► Fit the exhaust pipe.

► Fit the thermostat casing.

► Fit the fan.

More repair case for CLAAS,please refer to CLAAS Trouble Repair

auto

Recent Posts

How to Use Nexiq eTechnician Function Test?

Nexiq eTechnician provides a number of special tests to assist you with your vehicle diagnostic…

2 days ago

JCB JS140 Excavator P0523-68 Engine Oil Pressure Low Solution

Here car-auto-repair.com show you guide on how to repair JCB JS140 excavator P0523-68 trouble code…

3 days ago

Volvo Version 3 and 4 Truck Oil Pressure Test by Volvo Techtool

Here is the instruction show you guide on how to use Volvo TECHTOOL and VOCOM adapter to…

4 days ago

How to Solve Allison 3000 & 4000 Gen5 P071A Neutral at Stop Input Failed ON

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 transmission…

6 days ago

Mack and Volvo EPA13 GHG17 Engine NOx Conversion Monitor Test

This instruction show you guide on how to use JPRO TO perform Mack and Volvo…

1 week ago

Fendt 1100MT Tractor Code SA 00 SPN 3361 FMI 03

This instruction show you guide on how to solve Fendt 1100MT tractor trouble code SA…

2 weeks ago