Heavy Equipment Repair

CLAAS LEXION 8900 Benz/MAN Engine Oil and Oil Filter Changing Guide

Here is the instruction show you guide on how to change oil and oil filter for CLAAS LEXION 8900-5300 with Mercedes-Benz/MAN diesel engine.

 

Related Contents:

CLAAS CDS 7.5 Diagnostic Software 2021 2020 Free Download

CLAAS USB Interface Diagnostic Adapter Package

Claas WebTIC Offline Repair & Service 2024 2015 Free Download

 

 

Applies to: Mercedes-Benz diesel engine / MAN

Pre-condition:

Oil filter

O-ring

Multi-purpose grease

Oil collection container

Oil

Torque wrench 40 Nm for MAN diesel engine

Torque wrench 55 Nm for Mercedes Benz diesel engine

Drain the oil immediately after stopping the diesel engine at operating temperature. Dirt particles in the oil pan are flushed out along with the draining oil.

► Park the machine on level ground.

► Switch off and secure the machine.

► Clean the diesel engine and the surrounding area.

► Locate the oil filler neck and the oil filter in the diesel engine overview.

► Unscrew the oil filler neck.

 

► Unscrew lid (1) including filter (2) by 1 cm .

► Wait for the oil to run out of filter (2).

► Pull out lid (1) including filter (2) completely.

► Position hose at (1).

► Loosen nut (2).

► Collect the used oil in a suitable container.

► Tighten nut (2).

► Remove the hose.

 

Changing the oil filter

► Check if filter (3) contains foreign objects.

► Remove filter (3) by pressing laterally at the bottom edge of filter (3).

► Do not let any foreign objects end up in the filter housing!

► Never wipe out the filter housing.

► Replace sealing ring (2) of the lid.

Slightly grease sealing ring (2) with multi-purpose grease.

► Insert a new filter (3) into lid (1).

 

Applies to: Mercedes-Benz diesel engine

► Screw on lid (1) with the filter.

Tightening torque =  55 Nm

► Screw on lid (1) with the filter.

Tightening torque =  40 Nm

Topping up oil

 

NOTICE!

When the oil level is above the upper mark on the oil level dipstick, the diesel engine may be damaged.

► Top up oil no higher than up to the upper mark on the oil level dipstick.

► Top up fresh oil at the oil filler neck.

► Screw on the oil filler neck.

► Start the diesel engine.

Let the diesel engine run at slow idling speed for 10 seconds.

► Check if the oil filter is leaky.

► Check the oil level.

Top up fresh oil if necessary.

 

NOTICE!

Insufficient diesel engine oil pressure may cause diesel engine damage.

► After starting the diesel engine, watch the oil pressure indicator.

► If no oil pressure builds up 10 seconds after starting the diesel engine, stop the diesel engine immediately.

► Locate and remove the cause. If required, have the repair carried out by a qualified specialist workshop.

________________________________________

► Start the diesel engine.

Let the diesel engine run at slow idle speed for some minutes.

►  When this display appears, the diesel engine oil pressure is too low. Stop the diesel engine immediately. Have the fault removed by a qualified specialist workshop.

► Stop the diesel engine and wait for 10 minutes to allow the oil to flow back into the oil pan.

► Check the oil level.

Top up fresh oil if necessary.

More repair case for CLAAS,please refer to CLAAS Trouble Repair

auto

Recent Posts

QSK60 CM2358 Engine Camshaft Speed/Position Sensor Data Erratic Incorrect

This illustration show you guide on how to repair Cummings QSK60 CM2358 engine camshaft speed/position…

4 days ago

Fendt MT800E Tractor DEF Tank Temperature Does Not Change Solution

Here is the instruction show yo guide on how to solve Fendt MT800E tractor DEF…

6 days ago

HITACHI Construction 4JJ1 P0092 Fuel Pressure Regulator Control Circuit High

Here car-auto-repair.com show you guide on how to solve ISUZU construction 4JJ1 engine P0092 fuel…

1 week ago

How to Solve Perkins 1106D EPG Engine E398 Low Fuel Rail Pressure Error

Here is the illustration show you guide on how to solve Perkins 1106D electric power…

1 week ago

Deutz EMR3 Aassembly Inspection and Initialisation Test Guide

Here comes the instruction on how to use SerDia2010 to perform assembly inspection and initialization…

1 week ago

HITACHI ZX-5 Excavator No Load Max Differential Pressure Measurement Guide

This instruction show you guide on how to perform No load max differential pressure measurement…

1 week ago