Detroit Diesel GHG17 Engine Chassis Fuel System Isolation Test Guide

Detroit Diesel engine test is used to determine if the cause of a hard start or no start condition is on the engine side or the chassis side.This instruction show you guide on how to do chassis fuel system isolation test for Detroit Diesel GH17 heavy duty engine.

 

Related Contents:

2024.06 Detroit Diesel Diagnostic Link DDDL 8.20 8.09 Free Download

JPRO DLA+ 2.0 Adapter

NEXIQ USB Link Adapter

 

Procedures:

1 Prime the fuel system using a Detroit-approved priming unit.

Note : It is important that the road test is performed to purge the remaining air from the system after priming.

2 Disconnect the chassis-side fuel supply and return lines from the fuel filter module.

3 Using the appropriate adaptors from the W470589039100 Fuel System Tool Update Kit, install the two J-48708 Fuel Flow test lines onto the fuel filter module. Connect the other end of the test lines to the J-48708 fuel flow container. Container should have enough fuel to run a Fuel System Integrity Check (FSIC) and still have at least two liters (2.11 qt.) of fuel remaining.

Note:Do not move or otherwise disturb the Fuel System Update kit and the lines during the next two steps to ensure the ends of the lines remain submerged in fuel.

4 Prime the fuel system using the hand-priming pump.

5 Connect DiagnosticLink to the vehicle, access the Service Routines section, select the Fuel System Integrity Check (FSIC) tab and run the Automatic FSIC

 

WARNING

PERSONAL INJURY

Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.

  • Always start and operate an engine in a well ventilated area.
  • If operating an engine in an enclosed area, vent the exhaust to the outside.
  • Do not modify or tamper with the exhaust system or emission control system.

 

WARNING

PERSONAL INJURY

To avoid injury before starting and running the engine, ensure the vehicle is parked on a level surface, parking brake is set, and the wheels are blocked.

 

WARNING

ENGINE EXHAUST

To avoid injury from inhaling engine exhaust, always operate the engine in a well-ventilated area. Engine exhaust is toxic.

 

6 Wait 15 minutes and then restart engine to ensure there is not a hard start/no start condition.

 

7 Was there a starting issue?

7a Yes; verify all connections are tight and ensure that end of fuel lines remain submerged in fuel. Restart from step 4.

7b No; Go to step 8.

 

8 Allow engine to sit long enough for previous hard start/no start complaint to be verified.

 

9 Start engine.

 

10 Was there a starting issue?

10a Yes; the cause of the hard start/no start is on the engine side. Refer to section “Hard Start/No Start – Two-Filter Fuel System (This Test Must Be Done First)” to continue the diagnostics on the engine side.

10b No; the cause of the hard start/no start is on the chassis side. Check chassis fuel system lines per OEM procedures.

 

More repair cases for Detroit Diesel engines,please refer to:Detroit Diesel Engine Repair

auto

Recent Posts

QSK60 CM2358 Engine Camshaft Speed/Position Sensor Data Erratic Incorrect

This illustration show you guide on how to repair Cummings QSK60 CM2358 engine camshaft speed/position…

1 week ago

Fendt MT800E Tractor DEF Tank Temperature Does Not Change Solution

Here is the instruction show yo guide on how to solve Fendt MT800E tractor DEF…

1 week ago

HITACHI Construction 4JJ1 P0092 Fuel Pressure Regulator Control Circuit High

Here car-auto-repair.com show you guide on how to solve ISUZU construction 4JJ1 engine P0092 fuel…

2 weeks ago

How to Solve Perkins 1106D EPG Engine E398 Low Fuel Rail Pressure Error

Here is the illustration show you guide on how to solve Perkins 1106D electric power…

2 weeks ago

Deutz EMR3 Aassembly Inspection and Initialisation Test Guide

Here comes the instruction on how to use SerDia2010 to perform assembly inspection and initialization…

2 weeks ago

HITACHI ZX-5 Excavator No Load Max Differential Pressure Measurement Guide

This instruction show you guide on how to perform No load max differential pressure measurement…

2 weeks ago