Categories: How To

How to Connect Scania VCI3 to Scania Network or AdHoc

This instruction show you guide on how to use a Scania VCI3 remote connection,it describes how to setup the VCI3,and how to connect to it through the Scania network or AdHoc.

 

Related Contents:

Scania XCOM V2.30 V2.27 Dongle Emulator Free Download

How to Install Scania XCOM V2.30 Diagnostic Software

2024.07 Scania SDP3 V2.61.2 V2.40 Diagnostic Software Free Download

Scania VCI3 Interface

 

VCI3 configuration

Configuration of a VCI3 requires that SDP3 is installed.

1.Install latest SDP3. Available at:

Technical Information Library: https://til.scania.com/

OrderIT: http://orderit.scania.com/

 

2.Connect the VCI3 with USB to your computer

3.Run VCI Configurator

C:\Program Files (x86)\Scania\SDP3\VCIConfigurator.exe

 

4.Log in to the VCI3 (run factory reset if you have forgotten the password)

5.Enter “Connection password” and “Configuration password”.

6.Default settings for AdHoc connection:

7.Only if you have received permission:

Settings for network connected VCI3

8.Save configuration

 

 

Connect to network connected VCI3

Connect to a VCI3 that is connected to the Scania service network.

Connect to a remote VCI3 requires that SDP3 is installed.

1.Install latest SDP3. Available at:

o Technical Information Library: https://til.scania.com/

o OrderIT: http://orderit.scania.com/

2.Connect the VCI3 OBD connector to the vehicle and make sure you or someone else is supervising the vehicle.

 

3.Connect to the VCI3 by either by serial number or by listing available VCI3s on the network. See SDP3 manual for additional information.

4.Do not exit or disconnect SDP3. Start XCOM

5.Connect with XCOM as described in “Use case: Connect to CAN”

 

AdHoc connection to VCI3

WLAN is disabled on some laptops if it is docked or have a network cable connected!

An AdHoc connection means that you use the computer’s WLAN to connect to the VCI3.

To connect VCI3 AdHoc:

1.Connect the VCI3 OBD connector to the vehicle

2.Connect to the computer to the VCI3

3.Connect with XCOM as described in Use case: Connect to CAN

 

4.If the VCI3 can’t be found in XCOM:

a.Open “Control Panel” in Windows

b.Search and open “Kvaser Hardware”

c.Seach for Kvaser remote devices with Tools -> Select…

d.Select your VCI3, open properties for it and enter the connection password

e.Select the VCI3 and choose to connect to it. XCOM should find it now

auto

Recent Posts

Hitachi EX5600-7B Folding Stairway and Surrounding Parts Removal Guide

This instruction show you guide on how to remove folding stairway and surrounding part for…

1 day ago

Jungheinrich Junior AME13 Spring-Loaded Brake Electrical Connection Removal Guide

It is necessary step to remove electrical connection cable before you do disassemble or some…

3 days ago

How to Use Nexiq eTechnician Function Test?

Nexiq eTechnician provides a number of special tests to assist you with your vehicle diagnostic…

5 days ago

JCB JS140 Excavator P0523-68 Engine Oil Pressure Low Solution

Here car-auto-repair.com show you guide on how to repair JCB JS140 excavator P0523-68 trouble code…

6 days ago

Volvo Version 3 and 4 Truck Oil Pressure Test by Volvo Techtool

Here is the instruction show you guide on how to use Volvo TECHTOOL and VOCOM adapter to…

1 week ago

How to Solve Allison 3000 & 4000 Gen5 P071A Neutral at Stop Input Failed ON

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 transmission…

1 week ago