Categories: Auto Repair

How to Flash Automobile Steering Gear after Replaced by ODIS Engineering for VW

Why do we must use ODIS Engineering to replace steering gear?

Unlike 4S stores, the goods bought back are one-to-one correspondence, there are different procurement channels for parts in the other repair shop. For example, we can’t use steering gear 1K0909144 which we bought to replace the original steering gear of Volkswagen Passt 1K0909144 t, if so, the steering machine cannot learn the end position.

 

This instruction only focus on the third-generation ZF steering with 1K0, the second-generation steering machine starting with 1K1 and 1K2 is not clear whether it is feasible. Below is Firmware code comparison table

1KO 909144 C—–> 2301

1KO 909144 J —–> 3001

1KO 909144 M —–> 3201

1KO 909144 P —–> 3305

1KO 909144 R —–> 3501

The original firmware of the steering is 144P, you can directly flash Ih0013501.sgo.

If the file is upgraded to 144R,C,J,M, in order to ensure the safety of the steering, it is recommended to flash Ih0023305.sgo and then Ih0013501.sgo.

 

Preparation:

Newest ODIS-E Engineering 17.0.1/12.2.0/9.0.1 Free Download

08.2023 VW ODIS 23.0.5 & 7.2.1 & 5.2.7 Diagnostic Software Free Download

 

Procedures:

Put all Steering firmware files and Steering curve files to below storage path:

D:\Program File\Offboard_Diagnostic_Information_System_Engineering\datflash

Select “0044-Power Steering”–>”Vehicle function”–>”Vehicle special function”

Due to the differences between people and vehicles, the values of the channels might be different, so it is best to record the values of these channels.

Select “0044-Power Steering”–>”Data Selection”–”Programming”–>”Read Data”

Then save file to your computer

Open the report you saved previous, you can check the value of channel No.2-9.

Upload report you saved previous.

Click “Input Data”–>”Yes”

Input 8 channels

After finish it, Please reset the ignition switch. Click “Yes”

Navigate to the directory where the steering firmware and curve files are stored

Select “firmware 3305”, click “Open”

Upload first firmware flash file, then following 3501 and curve files

Upload the second Flash file in the same way

Finally upload the steering curve file v074N2398J0

Start flashing

Note: During the flash process, you will be required to turn off and turn on the ignition switch. You can continue without pulling out the key. This step is especially important. If you don’t restart the switch and click OK on the prompt, the flashing will fail.

Close all dialogs after flashing finished. Check steering number and curve are flash correctly on 44 power steering system.

After all the work is completed, you need to learn the G85 and the steering gear end position

Kevin

Recent Posts

Doosan Excavator P0408 Maximum EGR Rate Governor Deviation Error Solution

This instruction show you guide on how to solve Doosan excavator P0408 maximum EGR rate…

8 hours ago

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

3 days ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

5 days ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

1 week ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

2 weeks ago

How to Solve Fendt 800 Vario S4 wayline Running Slow

If the vehicle is oscillating on the wayline or catches up the wayline very slowly…

3 weeks ago