Categories: Auto Key Program

How to program key for BMW 525li 2013

Many primary auto locksmith believe that programming new key for bmw is difficult.Several days ago, a owner of bmw 525li leave key in the trunk and he can’t open.So i share the whole process here, how to program key for bmw 525li 2013. Hope it helpful!

After i meeting owner, i used auto locksmith too to open driver door and find it can’t open the trunk by trunk button.

In this situation,we need to remove one of back row seats.It is fixed by snap joint and easy to disassemble.You will find several screws after disassembling the seat,then remove screws.Put you hand in,find the switch to open the trunk. We get the key that owner leave in the trunk.Below we begin to program new key.

First,we need to disassemble the CAS module which locate after the accelerator pedal.(CAS of X1,3 Series is locate right of accelerator pedal)

Then,i use programmer APPRP to program.There is a wiring diagram on the software. You should to pay attention to CAS4+,because it need to be cut the line on PCB. Because the data read by programmer is encrypted,so you need to decode the data. And the just follow the remind to operate.Finally, place the new key on the steering wheel lock module while start car with original key.

Note 1: Read CAS Data.

Be sure to turn off one-start button before programming new key. BMW 525li 2013 equips with CAS4+ immobilizer system and 5M48H CPU. You can use the X-PROG or other programmer to read the data.It should noted that different programmer device need different wiring diagram, follow the usermanual to connect wiring correctly.Below show the wiring diagram of APPRP programmer and PCB wiring line cut way.After read out data, operate the software to decode data and save it.

Note 2: Check key state

Open APPRP programmer,select key tool–>select bmw 5 series 2012~–>click read key to check key state. Key is blank,OK.

 

Note 3:Use original key and CAS data to add new key.

Load DFlash data(read from 5M48H Chip),it will show information “key information,VIN”. Select a blacnk key position to generate dealer key.

Software display below information:

Type1: Generate dealer by original key

Type2:Generate dealer key by known synchronization code.

Type3:Generate dealer key by engine data.

Now begin to add new key, we select type 1:”Generate dealer by original key. After click “OK”,it will display below information

”please put original key into coil and click ok to continue.If the key you put into coil is not original key,it will can not start you car”

According to the remind to click “OK” button.

Then follow the information to put new key into coil.

Finally,it remind you “dealer key generate successfully”

auto

Recent Posts

Hitachi EX5600-7B Folding Stairway and Surrounding Parts Removal Guide

This instruction show you guide on how to remove folding stairway and surrounding part for…

32 mins ago

Jungheinrich Junior AME13 Spring-Loaded Brake Electrical Connection Removal Guide

It is necessary step to remove electrical connection cable before you do disassemble or some…

2 days ago

How to Use Nexiq eTechnician Function Test?

Nexiq eTechnician provides a number of special tests to assist you with your vehicle diagnostic…

4 days ago

JCB JS140 Excavator P0523-68 Engine Oil Pressure Low Solution

Here car-auto-repair.com show you guide on how to repair JCB JS140 excavator P0523-68 trouble code…

5 days ago

Volvo Version 3 and 4 Truck Oil Pressure Test by Volvo Techtool

Here is the instruction show you guide on how to use Volvo TECHTOOL and VOCOM adapter to…

6 days ago

How to Solve Allison 3000 & 4000 Gen5 P071A Neutral at Stop Input Failed ON

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 transmission…

1 week ago