Categories: Auto Coding

How to register a new BMW Battery after replacement

You need to register bmw battery after replacing bmw battery.Because BMWs need to know battery capacity and battery type….YOU DO NEED TO REGISTER battery replacements on BMWs with an IBS (Intelligent Battery Sensor).In this article you will get skill of how to register bmw battery with Rheingold ISTA.And here is another article about BMW Battery Registion:

How To Use INPA Register BMW 7 Series New Battery

Rheingold ISTA Register New Battery for BMW F10 

 

BMW Rheingold ISTA Software Free Download

2024.08 BMW Rheingold ISTA+ 4.48.40 4.23.14 ISTA-P 3.71 Free Download

Why need to register the battery after replacement?

After installing a new battery, the service function ‘Register battery replacement’ must be run. The registration of the battery replacement is required to inform the power management (software in engine electronics and intelligent battery sensor) that a new battery was installed in the vehicle. If the battery replacement is not registered, the power management will not function properly and can lead to functions being limited by individual electrical consumers being switched off or having their power consumption reduced. Power management will charge the new battery as if it’s the old worn out battery, causing premature failure of the replacement battery.

Important! If the new battery is not registered, incorrect readings may appear in the display of the on-board computer due to old data in the power management system (check control message ”Recharge battery” appears even though the battery is new).

A service function informs the power management in the Digital Engine Electronics (DME) or the Digital Diesel Electronics (DDE) of a battery replacement. The following operations are performed:

-The current mileage reading is stored for the battery replacement.

-The stored measured values (battery charge statuses, current, voltage, temperature, etc.) are deleted.

-The power management is initialized.

Available registration options:

  1. Replacing battery with exact same type – (Simple registration)
  2. Replacing battery with same type but different capacity – (Registration/Conversion)
  3. Replacing battery with different type – (Programming/Conversion/Registration)
  4. Updating software of complete battery management system

 

Changes to the charging profile also affects how the Start/Stop system works for vehicles with EfficientDynamics

 

Car 1:

You’re renewing the battery with identical replacement. You register replacement to let the car know that the battery is new and the charging profile is adjusted accordingly. If you don’t the vehicle will charge for an old battery and cause premature failure.

 

Car 2:

You fit an AGM in place of a Standard LA battery (or vice versa). If you don’t register the replacement then it will toast the new battery for similar reasons to Car 1 but even worse as the charging profile will be for the incorrect type battery and cause even faster battery failure. In this case you MUST use a ‘conversion’ to change the battery type. Then, register a replacement.

BMW Register battery replacement

Notice! Determination of state of charge after a battery replacement

 

After a battery replacement, the vehicle must be left standing for at least 3 hours with its new battery. It is not possible to establish with any reliability the state of charge of the new battery until that time. Possible Check Control messages about total discharge of the battery are then no longer displayed.

BMW battery state of charge

Notes for disconnecting and connecting battery

The scope of application of some systems may be restricted after a power supply interruption. Likewise, individual settings may be lost.

Settings or activations must be carried out, depending on the equipment specification. For example:

 

Vehicles with automatic engine start‐stop function (MSA): MSA function is active only after learning period (vehicle must not be woken for a period of approx. 6 hours

E46 Perform (four-wheel drive) / E53 / E83: steering angle sensor adjustment

If necessary, activate slide/tilt sunroof

If necessary, activate power windows

If necessary, activate mirror with compass

 

Only E60, E61, E63, E64, E70, E71, E90, E91, E92, E93: mount steering angle

Skipping the battery registration process can dramatically shorten the life of a battery in these vehicles, be it an AGM or a conventional battery. Several issues can cause premature battery failure, see post on Energy Diagnosis, but on a late model BMW, skipping battery registration can be one of them.

auto

Recent Posts

QSK60 CM2358 Engine Camshaft Speed/Position Sensor Data Erratic Incorrect

This illustration show you guide on how to repair Cummings QSK60 CM2358 engine camshaft speed/position…

5 days ago

Fendt MT800E Tractor DEF Tank Temperature Does Not Change Solution

Here is the instruction show yo guide on how to solve Fendt MT800E tractor DEF…

1 week ago

HITACHI Construction 4JJ1 P0092 Fuel Pressure Regulator Control Circuit High

Here car-auto-repair.com show you guide on how to solve ISUZU construction 4JJ1 engine P0092 fuel…

1 week ago

How to Solve Perkins 1106D EPG Engine E398 Low Fuel Rail Pressure Error

Here is the illustration show you guide on how to solve Perkins 1106D electric power…

1 week ago

Deutz EMR3 Aassembly Inspection and Initialisation Test Guide

Here comes the instruction on how to use SerDia2010 to perform assembly inspection and initialization…

1 week ago

HITACHI ZX-5 Excavator No Load Max Differential Pressure Measurement Guide

This instruction show you guide on how to perform No load max differential pressure measurement…

2 weeks ago