Categories: Do It YouselfHow To

How to Replace Fuel Filter for Mercedes Benz C350

A clogged and faulty fuel filter can cause poor engine performance. When they get completely clogged you may be left with an engine that doesn’t run at all. If you are getting an error code for the pump make sure to replace it right away before it leaves you stranded on the side of the road.Here I want to share fuel filter for Mercedes Benz C350.

 

Applies to: C350 (2007-14), C180 (2007-14), C200 (2007-14), C230 (2007-14), C250 (2007-14), C280 (2007-14), C300 (2007-14), C320 (2007-14)

 

Time: 3 hours

Tab: $100 to $190

Talent: 2

Tools:8mm socket, large flathead screwdriver, hammer

Parts Required: Fuel filter, fuel filter-sealing O-ring

Hot Tip: Be careful working around gas

Performance Gain: Better running engine

Complementary Modification: Detail the interior

 

Mercedes Benz C350 Fuel Filter Replacement:

Begin by opening the fuel filter door and removing the gas cap.This will help relieve pressure in the system.

You will need to disconnect the fuel line from the pump to replace the filter.In our project car so you need to access both the filter and pump.Both are located under the rear seat with the pump on the right side (red arrow) and the filter on the left (yellow arrow).You need to remove the rear seat,see my article on bench seat removal:How to Replace Bench Seats for Benz W204

There are two fuel lines that need to be disconnected from the fuel pump to the right side (red arrow).Please see my article on fuel pump replacement:How to Replace Fuel Pump for Mercedes Benz C350

With the rear seat removed you can see the access cover for the fuel filter.Use a 8mm socket and remove the four bolts (red arrows).Lift the cover off taking care to peel away the sealant gasket around the wiring connection.

The filter is located under the access cover.Begin removing it by disconnecting the two electrical connections (red arrows).Then give a good cleaning around the retaining ring and lid.

You will need to remove the locking ring that holds the filter in place in the gas tank.While Mercedes makes an expensive tool for doing this if you are careful you can use a large flathead screwdriver and small hammer and gently tap the ring back off the tabs.Use the holes in the outer retaining ring and tap evenly around the entire outside of the ring.Do not just start hammering away on one spot.Instead,continuously move around the ring.

There should be a witness mark on the ring (red arrow) that will let you know when it is fully locked (the one on the photograph is unlocked).With the ring unlocked remove the fuel line by squeezing in the tab and lifting it off the filter (yellow arrow).A little fuel will spill out so be prepared to catch it and dispose of it correctly.

Remove the retaining ring and note the position of the filter in the tank.The large tab on the front of the filter must face towards the front of the vehicle (red arrow).You can now lift the filter out from the tank.Use care that you do not bend or damage the left side level detector (red arrow).Remove the filter with the hoses to the pump (yellow arrow) attached.The fuel pressure sensor is attached to the top of the filter and can be transferred to the new filter by removing the retaining ring and installing it the new filter.Please see my article on fuel pressure sensor replacement:How to Replace Fuel Pressure Sensor for Mercedes Benz

Installation is the reverse of removal.Make sure that the lid is positioned and sealed correctly.

 

 

auto

Recent Posts

Doosan Excavator P0408 Maximum EGR Rate Governor Deviation Error Solution

This instruction show you guide on how to solve Doosan excavator P0408 maximum EGR rate…

1 day ago

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

3 days ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

6 days ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

1 week ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

2 weeks ago

How to Solve Fendt 800 Vario S4 wayline Running Slow

If the vehicle is oscillating on the wayline or catches up the wayline very slowly…

3 weeks ago