Categories: Truck Repair

How to Reset/Upload ECM Data for ISUZU 2020 4JJ3 Truck

When replacing the ECM, the vehicle data must be written into the new ECM.The scan tool used for the replacement procedure must be the same from start to finish. If the scan tool is changed midway, information cannot be written correctly.So this instruction show you guide on how to reset/upload ECM data for ISUZU 2020 4JJ3 AWR6B45 truck.

Use the following procedure when replacing or programming the ECM.

 

Preparations:

Isuzu G-IDSS Export 2023 2019 Diagnostic Software Free Download

ISUZU US-IDSS II 2024 2019 Diagnostic Software Free Download

 

Note:

*1: If reusing the ECM in another vehicle, perform the ECM reset in the original vehicle.

*2: Perform only for models with immobilizer.

Caution:

Because “ECM reset” cannot be performed in a new vehicle, be sure to perform “ECM reset” in the original vehicle.

 

1.ECM Reset

Caution:

When installing the ECM to the vehicle, it must be security linked to the wireless access module using the programming procedure. Once this linking has been performed, the ECM cannot be installed to any other vehicle. Before transferring (switching) to the vehicle in which the complaint originated, the resetting procedure must be performed in the original vehicle and the security linkages between each module must be reset.

 

If the ECM to be replaced cannot establish communication with the scan tool, do not perform this operation.

1) Connect the scan tool to the DLC.

2) Turn ON the ignition switch.

3) Select the scan tool item.

Diagnostics > Body > WAM (Wireless Access Module) > Special Function > Engine Control Module > Reset Engine Control Module

4) Erase the immobilizer information of the ECM by following the on-screen instructions.

 

Caution:

Entering an incorrect security code causes a security wait time.

Note:

When turning the ignition switch ON and OFF by following the on-screen instructions, wait at least 5 seconds before turning it OFF or ON each time.

5) Turn OFF the ignition switch for 30 seconds.

6) Verify that the engine does not start with all the keys.

 

2.ECM data upload

1) Upload the following data from the old ECM to the scan tool.

 

Injector ID Code

Vehicle speed correction data

3.Injector ID code upload

1) Connect the scan tool to the DLC.

2) Turn ON the ignition switch.

3) Select the scan tool item.

Diagnostics > Engine > 4JJ3 > Programming > Injector ID Code > Upload Injector ID

4) Follow the directions on the screen and upload the injector ID codes to a scan tool.

 

4.Vehicle speed correction data upload

1) Turn ON the ignition switch.

2) Select the scan tool item.

Diagnostics > Engine > 4JJ3 > Programming > Vehicle Speed Correction Data > Upload Vehicle Speed Correction Data

3) Upload the vehicle speed correction data to the scan tool by following the on-screen instructions.

4) After completing the upload, turn off the scan tool.

5) Turn OFF the ignition switch.

auto

Recent Posts

JCB JS140/205/215 Excavator C1022-13 Coolant Temperature Sensor Open Circuit

This instruction show you guide on how to solve JCB JS140/205/215 excavator C1022-13 trouble code coolant…

2 days ago

How to Diagnostic and Repair PCC1302 PowerCommand Code 2972 – Field Overload

If the time that the Field AVR Duty Cycle is operating at maximum output is…

3 days ago

Caterpillar C9 Engine 15 164-3 Injection Actuation Pressure Voltage High

The Engine Control Module(ECM) detects the following conditions: The voltage for the injection actuation pressure…

4 days ago

Volvo and Mack EPA 10 Engine Hydrocarbon Dosing Control Valve Test by JPRO

This instruction show you guide on how to perform hydrocarbon dosing control valve test for…

1 week ago

Fendt Tractor SPN 100 FMI 31 Oil Pressure Sensor Defect Solution

This instruction show you guide on how to solve Fendt tractor SPN 100 FMI 31…

1 week ago

Detroit GHG17 Heavy Duty Engine Piston Protrusion Measurement Procedure

Detroit GHG17 Heavy Duty Engine Piston Protrusion Measurement Procedure   Related Contents: 2024.06 Detroit Diesel…

2 weeks ago