Categories: Auto Key Program

How to Use Zed-Full Program Key For Fiat Egea (OBD Can’t Support)

This illustration show you guide on how to use Zed-Full programmer to add new key for Fiat Egea.And for more Zed-Full cases,please check here:Zed-Fll Test Feedback

 

Note:If your Fiat BSI module can support pre-coded by OBD,check procedures here: How to Use Zed-Full Program Keys for Fiat Egea by OBD

 

Procedures:

Connect Zed-full to Fiat Egea OBD port

Enter menu to select OBD application

Select “Fiat”–>”Fiat-EU”

Select “Immobiliser”–>”Pre-coding chip”

 

Select system “Delphi Meg.AES chip NEC MCU”

Turn ignition ON then press “Continue”

Current,reading car data from BSI through OBD is not supported.Please follows these steps respectively;

1.Remove BSI module from the car and use 265the eeprom module to get required car datat

2.Inert BSI module back to car and follow OBD key programming steps

Remove BSI unit which is just under the steering wheel

You must solder 1KΩ Resistor between blue and red cables of the ZFH-C07/ZFH/C07-2 cable

After eeprom/MCU application BSI unit must be reinstalled to the vehicle and new key should be programmed via OBD

Back main menu to select “Eeprom and MCU”

Select “Fiat”–>”Module 265 NEC D70F3556…”

Clcik “App.Info”,you may see more details

Connect ZFH-C07 cable socket to Zed-FULL

Press “Continue button”

Select Eeprom or MCU type to be read from the list and press “Continue” button

Select “Read In Circuit”

Ensure that all wire and socket connection are OK and press “Read” button

Reading Eeprog/MCU is successful.Zed-Full programmer will keep the car data on its internal memory.Process will continue with OBD application on car.

Desolder ZFH-C07 cable wires from BSI and insert unit back to the car

After then select “OBD application”–>”Fiat”–>”Fiat ECU”–>”Immobiliser”–>”Pre-coding”–>”Delphi Meg.AES chip NEC MCU” respectively.

Then turn ignition ON and press “Continue” button

Connection is successful!

Car VIN number,pin code and key ID will be shown on Zed-Full screen

New key to be programmed must be precoded first.

Press “Continue” button

Put new key to be precoded to Zed-Full antenna and press “Continue” button

Pre-coding written

Press “No” to exit transponder precoding procedure

Press “Continue” button to program precoded transponders to the car

All non-programmed working key will be erased from cacr memory irreversibly and can not be programmed again.

Car has two working keys,we will add 1 key,so we enter 3 as total key quantity

Working key was already on ignition and ignition was “ON”,press “Continue”

1st key is on ignition,press “Continue” button

Put 2nd key to ignition and press “Continue” button

Put new key to be programmed (3rd key) to ignition and press “Continue” button

Programming successfully!

Now you can test all programmed keys

 

More FIAT key programming,check this article collection:Fiat Key Programming

auto

Recent Posts

Doosan Excavator P0408 Maximum EGR Rate Governor Deviation Error Solution

This instruction show you guide on how to solve Doosan excavator P0408 maximum EGR rate…

2 days ago

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

4 days ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

7 days ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

1 week ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

2 weeks ago

How to Solve Fendt 800 Vario S4 wayline Running Slow

If the vehicle is oscillating on the wayline or catches up the wayline very slowly…

3 weeks ago