How to: XENTRY SCN Coding for Mercedes Benz S221

SCN coding is also required to prevent any aftermarket enhancements that are done to improve the performance. If you want to install additional control module in the future, it will require SCN coding.Here I want to share how to use Xentry perform SCN Coding for Benz S221.Hope it helps!

 

Preparations:

Newest Mercedes-Benz Xentry.OpenShell.XDOS 06.2023 Free Download

How to Install Benz Xentry 2023.06 Diagnostic Software

Xentry OpenShell Patcher Edition v3.3 Download for Win 7/8/10

MB SD Star C4

 

Procedures:

Connect MB SD device between laptop and the vehicle.

Launch Xentry software

Automatic vehicle determination

Then it will prompt with below warning massage

“Information on preventing damage to electronic components due to electrostatic discharge:

The safety information and descriptions listed in Help(F6) MUST be observed….

General test conditions:

….”

Click “F2” to continue

Data being determined,please wait…

Click “F2” to continue

Data being determined,please wait…

Please wait,DAS is initializing communication layer.

It will show you with massage

Important:increased power requirement with ignition ON.

IMPORTANT NOTE:

Ensure power supply during the diagnosis session

The battery must not have undervoltage when the vehicle is handed over to the customer

If necessary,recharge the battery beforehand.

……

Click “F2” to continue

Data are being determined,please wait…

Communication with control unit AAC is being established.

Select “Quick test” and click “F3” to continue

Data are being determined,please wait…

Communication in progress

Select “M9.7-Motor electronics 9.7”

 

Select “I herewith confirm that I have read the safety notes”

Then click “F3” to continue

Communication with control unit ME9.7 is being established

Data are being determined,please wait…

Select “Control unit adaptations”

Select “Variant coding”

Communication with control unit ME9.7 is being established

Data are being determined,please wait…

Select “SCN Coding” and click “F3” to continue

Data are being determined,please wait…

Loading the data record,please wait…

User data are checked.

It will prompt you with below massage,click “F3” to continue

Here you need to input your Mercedes Benz online account for SCN coding

Verification of access authorization to establish an Internet connection

Data being determined,please wait…

SCN coding data are being requested from headquarters,please wait…

Communication with control unit ME9.7 is being established

The coding is being carried out,please wait

Follow Xentry software operation to switch off ignition

Wait…

Switch on ignition

Control module reset,please wait…

Data are being determined,please wait…

Then it will show the information of Documentation for repair order+”VIN”

The SCN coding sequence has been completed successfully

….

Done!

auto

Recent Posts

Jungheinrich Junior AME13 Spring-Loaded Brake Electrical Connection Removal Guide

It is necessary step to remove electrical connection cable before you do disassemble or some…

2 days ago

How to Use Nexiq eTechnician Function Test?

Nexiq eTechnician provides a number of special tests to assist you with your vehicle diagnostic…

4 days ago

JCB JS140 Excavator P0523-68 Engine Oil Pressure Low Solution

Here car-auto-repair.com show you guide on how to repair JCB JS140 excavator P0523-68 trouble code…

5 days ago

Volvo Version 3 and 4 Truck Oil Pressure Test by Volvo Techtool

Here is the instruction show you guide on how to use Volvo TECHTOOL and VOCOM adapter to…

6 days ago

How to Solve Allison 3000 & 4000 Gen5 P071A Neutral at Stop Input Failed ON

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 transmission…

1 week ago

Mack and Volvo EPA13 GHG17 Engine NOx Conversion Monitor Test

This instruction show you guide on how to use JPRO TO perform Mack and Volvo…

2 weeks ago