Categories: Truck Repair

ISUZU 4JJ1 N Series Truck Gearcase Assembly Removal and Installation

This instruction show you guide on how to remove and install gearcase assembly for ISUZU 4JJ1 Euro 4 N series truck.More repair cases please refer to:ISUZU Trouble Repair.

 

Related Contents:

ISUZU US-IDSS II 2024 2019 Diagnostic Software Free Download

ISUZU Worldwide EPC 2018.03 Snap-on EPC Installation Service

 

Procedures:

Removal

1.Remove the engine assembly from the vehicle.

2.Remove the cylinder head.

3.Remove the generator bracket.

4.Remove the vacuum pump.

5.Remove the power steering pump.

Remove the power steering pump at the engine side with the hose attached.

Fasten the power steering pump with hose attached to any suitable position with a wire.

6.Remove the water pump.

7.Remove the fuel supply pump.

8.Remove the crank pulley.

9.Remove the gearcase cover.

10.Remove the idle gear A, idle gear A shaft, idle gear C, and idle gear C shaft.

11.Remove the oil pump.

12.Remove the gearcase(1) and gasket(2).

NOTE: Do not remove the bolt(10) when attaching/detaching the gearcase.

 

Installation

1.Install the gasket.

Apply liquid gasket(TB-1207B or equivalent) to the area indicated in the diagram(1).

The gasket applies it to the both sides

After applying the liquid gasket, install the gearcase within five minutes.

2.Install the gearcase.

Align the positions of the dowel pin and bolt and install the gearcase.

Do not remove the bolt(10) when attaching/detaching the gearcase.

3.Install the oil pump.

4.Install the idle gear A, idle gear A shaft, idle gear C, and idle gear C shaft.

5.Install the gearcase cover.

6.Install the crankshaft pulley.

Install the crankshaft pulley, washer and bolt and tighten them at the specified torque. At this time, apply engine oil to the bolt seat surface and threaded portion.

Tightening torque:185 N.m(18.9kg-m/137 lb-ft)

NOTE: Do not reuse the bolt and washer of the crankshat pulley.

7.Install the fuel supply pump.

8.Install the water pump.

9.Install the power steering pump and tighten it at the specified torque.

Tightening torque:25N-m(2.5kg-m/18 Ib-ft)

10.Install the vacuum pump.

11.Install the generator.

12.Install the cylinder head.

13.Install the engine assembly to the vehicle.

auto

Recent Posts

How to Solve Allison 3000 & 4000 Gen5 Engine Trouble Code P0703

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 engine…

2 days ago

How to Solve Fendt MT1149 Tractor SCR System Emptying Not Completed

Here is the illustration show you guide on how to solve Fendt MT1149 tractor SCR…

1 week ago

How to Set Play Between Timing Pinion Teeth for CLAAS AXION 920 Tractor?

Here is the instruction show you guide on how to set play between timing pinion…

1 week ago

Perkins 1106D Generation Injector Data Incorrect Test Guide

Perkins 1106D Generation Injector Data Incorrect Test Guide   Preparations: Perkins EST 2024A & 2023A…

1 week ago

How to Solve Deutz EMR3 Engine Error 16/108/APSCD Trouble

This instruction show you guide on how to solve Deutz EMR3 engine error 16/108/APSCD trouble…

2 weeks ago

Kubota L4701 High Pressure Relief Valve Pressure Checking

Here show guide on how to check high pressure relief valve pressure for Kubota L4701…

2 weeks ago