Categories: Auto Repair

ISUZU Truck Control Module Failed Reprogramming Attempt Solution

Some customers may experience various warning lights, reduced vehicle speed or a no start condition. Technician diagnosis may reveal one or more CAN communication error related DTCs and at least one control module will not communicate with IDSS. This condition was most likely caused by a failed reprogramming attempt of a control module.More ISUZU trouble please check here:ISUZU Trouble Repair

IMPORTANT: DO NOT REPLACE THE CONTROL MODULE.

It is possible to recover a control module after a failed programming attempt. Follow the service procedure below in order to recover a control module after a failed programming attempt or when IDSS cannot communicate with the control module.

 

ISUZU E-IDSS 2023 2019 Engine Diagnostic Service System Free Download

ISUZU IDSS MX2-T

 

SERVICE PROCEDURE

1.Instructions for Control Module Recovery Fully close IDSS.

2.Disconnect the IDSS interface module connector from the vehicle data link connector (DLC) [if connected].

3.Turn OFF the ignition and wait 1 minute.

4.Connect IDSS to the vehicle DLC and the PC USB port (if not already connected).

5.Turn ON the ignition with the engine OFF.

6.Open IDSS.

7.Choose the correct vehicle information on the IDSS Main screen and then click Submit.

8.Click on Controller Programming from the table of contents.

IMPORTANT: The left IDSS bulb on the ICON toolbar MUST be green at this point indicating IDSS is connected to the vehicle AND is talking to the PC USB port. If it is still red, check that the IDSS interface module is being powered up by making sure the IDSS interface module power LED is red. If it is red, then the PC may not be talking with the USB port and a PC reboot may be necessary.

 

9.If IDSS automatically goes to a VIN screen under Engine Control Module (ECM) Programming > Software and Calibrations > Replace and Reprogram Controller, go to Step 10. Otherwise, go to Step 18.

10.Enter the correct 17-digit VIN at the VIN enter screen, then click Next.

11.A pop-up message will occur stating the VIN has been changed. Confirm the correct VIN was entered, and then click Yes.

12.Do NOT turn OFF the ignition at the Install New Controller screen. Click NO when asked is the Original Controller installed.

13.Click Reprogram Controller at the Summary of Calibrations screen. Programming should begin.

 

NOTE:The controller is accepting the download IF the programming dialogue Sending Bytes is incrementing. The Sending Bytes incremental counter normally begins at around 20-30 seconds.

14.When instructed to do so after the programming event has finished, turn OFF the ignition and wait for the counter to finish counting down.

15.Turn ON the ignition with the engine OFF, then clear all DTCs.

16.If this is a new ECM, program the Speedometer Calibration, Fuel Injector Flow Rates and any associated Vehicle Options.

17.Go to Step 24.

18.Navigate to the control module to be reprogrammed, and then choose Software and Calibrations > Replace and Reprogram Controller.

19.Enter the correct 17-digit VIN at the VIN enter screen, then click Next.

20.Do NOT turn OFF the ignition at the Install New Controller screen. Click NO when asked is the Original Controller installed.

NOTE:The controller is accepting the download IF the programming dialogue Sending Bytes is incrementing. The Sending Bytes incremental counter normally begins at around 20-30 seconds.

21.Click Reprogram Controller at the Summary of Calibrations screen. Programming should begin.

22.When instructed to do so after the programming event has finished, turn OFF the ignition and wait for the counter to finish counting down.

23.Turn ON the ignition with the engine OFF and clear all DTCs.

24.Programming is complete.

auto

Recent Posts

Hitachi EX5600-7B Folding Stairway and Surrounding Parts Removal Guide

This instruction show you guide on how to remove folding stairway and surrounding part for…

1 hour ago

Jungheinrich Junior AME13 Spring-Loaded Brake Electrical Connection Removal Guide

It is necessary step to remove electrical connection cable before you do disassemble or some…

2 days ago

How to Use Nexiq eTechnician Function Test?

Nexiq eTechnician provides a number of special tests to assist you with your vehicle diagnostic…

4 days ago

JCB JS140 Excavator P0523-68 Engine Oil Pressure Low Solution

Here car-auto-repair.com show you guide on how to repair JCB JS140 excavator P0523-68 trouble code…

5 days ago

Volvo Version 3 and 4 Truck Oil Pressure Test by Volvo Techtool

Here is the instruction show you guide on how to use Volvo TECHTOOL and VOCOM adapter to…

6 days ago

How to Solve Allison 3000 & 4000 Gen5 P071A Neutral at Stop Input Failed ON

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 transmission…

1 week ago