Categories: Auto Repair

Mercedes Benz Airbag Reset by Carprog

Mercedes Benz airbag sensor after car crash and airbag deployment can by locked (Control unit faulty) and must be replaced. Even after small accident Airbag sensor will write in internal memory special error message “crash data stored” or “computer fault” and after you need to exchange very expensive sensor to new one. With our MB Airbag Reset Tool you can reset and repair airbag computer in your office in 1 minute.

We are glad to present new device for MB Airbag repair. You can see some differences between

old and new devices bellow:

Link to PC Read DTC Error Clear DTC Error Clear Crash Data EEPROM Read/Write
Old Tool Serial +/- + +/-
New Tool USB + + + +

 

 

Carprog Software:

Latest Carprog Crack v10.93 Free Download

How to Install Original & Crack Carpog Full V10.93 Software

 

 

ECU types supported by MB Airbag Rest Tool:

 

No need to remove from car!

EEPROM read/write, Crash Data clear,

Error Memory read/erase.

Pin 9 – K line

Pin 5 – +12V

Pin 6 – GND

 

 

No need to remove from car!

EEPROM read/write, Crash Data clear, Error

Memory read/erase.

Pin 9 – K line

Pin 5 – +12V

Pin 6 – GND

 

 

No need to remove from car!

EEPROM read/write, Crash Data clear, Error

Memory read/erase.

Pin 9 – K line

Pin 5 – +12V

Pin 6 – GND

 

 

No need to remove from car!

EEPROM read/write, Crash Data clear,

Error Memory read/erase.

Pin 9 – K line

Pin 5 – +12V

Pin 6 – GND

 

 

No need to remove from car!

EEPROM read/write, Crash Data clear,

Error Memory read/erase.

Pin 32 – K line

Pin 1 – +12V

Pin 56 – GND

 

 

No need to remove from car!

EEPROM read/write, Crash Data clear,

Error Memory read/erase.

Pin 32 – K line

Pin 1 – +12V

Pin 56 – GND

 

Using these pictures you can erase airbag “on the table” – you must connect GND, +12V,And Diagnostic line between airbag sensor and MB Airbag Eraser, connect power supply to GND and +12V and use Eraser like in the car. After erasing don’t connect power supply again – MB airbag sensor is very sensitive and can write “controller malfunction” error after connection on the table without car.

 

OBDII – MB 38 pin connection diagram :

Mercedes Benz Connector Mercedes Benz 38 Pins Connector
7 30(Diagnostic)
13 30(Diagnostic)
16 3(+12V)
4 1(GND)
5 1(GND)

 

auto

Recent Posts

Doosan Excavator P0408 Maximum EGR Rate Governor Deviation Error Solution

This instruction show you guide on how to solve Doosan excavator P0408 maximum EGR rate…

1 day ago

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

3 days ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

6 days ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

1 week ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

2 weeks ago

How to Solve Fendt 800 Vario S4 wayline Running Slow

If the vehicle is oscillating on the wayline or catches up the wayline very slowly…

3 weeks ago