Categories: Auto Coding

Mercedes Benz E-series(212,207) 2010 Headlight Coding Guide(Video)

An error of “Headlamp not coded/programmed” will be generated after replacing the headlamp functional module on Mercedes-Benz E-serial models. It is necessary to perform the headlamp coding at this time. Otherwise,the headlamp can only provide the lighting function and won’t be able to adjust the low beam and high beam.Here comes the easy guide on how to coding headlight for Mercedes Benz E-series(Chassis 212,207).And watch the video guide at end of article to get more detail.Let’s make a deep breathe…and here we go

 

Here are some articles about headlight,maybe you also like:

BMW X5 3.0Si Self-adaptive Headlights Repair

How to restore headlight by yourself

 

What device you need for coding headlight on Benz E-series?

There are many device you can choice to do this function,and here I take the X431 device as example.

 

NOTES:
1. If still unable to work normally after the coding completed, turn ignition off, then on again in about 1 minute, and try to switch between the high beam and low beam again. It will work.
2. If only one side headlamp has been replaced, the other side works normally, first enter the normal headlamp system to read and record all codes. Then enter the abnormal headlamp system to code. Set the code same as that in normal side system.
3. If the code is set incorrectly by accident, select the correct code and reset. The code can be changed repeatedly under this function.

 

Procedures of Benz E-series headlight coding guide:

Connect X431 device to vehicle,and enter menu to select MERCEDES-Benz V48.20.

Note:This program diagnose Mercedes electronic control systems,including:Power,Chassis,Body,Info,Seat & Door,AC/etc.

Select “Manually Select”

Select “2112-E Class”

Screen show that”Now is reading mileage from ECU,Please wait…”

Select “Sedan”

Select “Gasoline Engine”

Select “Left Hand steering”

Select “Chassis 212.056–E 350”

Select “Select “Control Units”

Select “Body”

Select “XALWA-L-Left Xenon Headlamp(E1n1)”

Scanning CAN system,please wait…

Select function of “Variant Coding

Select “Vehicle data record-General”

The above items will be listed

Select each menu in sequence to proceed

Select “Vehicle data record-General”

Select “BiXenon”

Select “Write Coding” button

Click “No”,no operation will be performed

Clcik “Yes”,it performs “write code” and displays “turn ignition off”

After turnning ignition off,click OK,then it shows “turn ignition on”

The coding has been performed

Done!

Video guide on Mercedes Benz E-series(212,207) 2010 Headlight Coding

auto

Recent Posts

How to Remove Second Tank for CLAAS AXION 960-920 Tractor

This instruction show you guide on how to remove second tank for CLAAS AXION 960-920…

49 mins ago

Doosan Excavator P0408 Maximum EGR Rate Governor Deviation Error Solution

This instruction show you guide on how to solve Doosan excavator P0408 maximum EGR rate…

3 days ago

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

5 days ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

1 week ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

2 weeks ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

3 weeks ago