Categories: Auto Repair

Mitsubishi 2009 B2206 Chassis Number Matching by X431

This article show a guide on how to match B2206 chassis number for Mitsubishi 2009.I will write up by text and pictures at first part,and for more detail info to watch the video guide at end of article.

 

Mitsubishi 2009 B2206 Chassis Number Matching

Connect the X431 v8 to vehicle,then enter the system to select “MITSUBISHI V32.00”

Note:The software can diagnose the elec,control sys of MITSUBISHI,include ENGINE/AT/ABS/SRS and other parts.The function is the same as the original scan tool.

Initializing communication,please wait…

Scanning VIN…

Communicating,please wait…

Searching VIN…

It prompts that the matched VIN(S) can’t be found select ok

Select “As of 2006”

Select “Other”

Select “OUTLANDER/OUTLANDER EX (CW#)”

Select “2009”

Select “CW5W”

Select “XTSHZL1C”

It prompts the vehicle information,select “ok”

Select “Health Report”

Select “Fault report”,it prompt that the B2206 Chassis number error was mismatch

Select “MPI/GDI/DIESEL”

Initializing communication,please wait…

Then the system will prompt the ECU information,select ok

Select “Version Information”

Reading ECU information…

It prompts that the ECU information,select ok

Processing,please wait…

Select “IMMOBI & Keyless”

It prompts that the ECU information as below,select ok

ECU info:

ECU ID:04640050

Please write down the information or print this page for consultation in aftersales service center.

Select “Version Information”

Reading ECU information…

It prompts that the ECU information ,select ok

Select “Special Function”

Please pay more attention to the Hints as below,select yes.

Hints:

Note:because it needs the professional knowledge for registration,so when you select,delete or reset the item related with the security key,please pay attention to the selected item an execution.

Select “ENGINE KEY CODE REG.&VIN WRITING”

It prompt”Are you sure to operform this function?”

Select “Yes”

It prompts that the key code registered to the engine ECU,select “OK”

It prompts that the key registration is completed,select “OK”

Then input the VIN,select ok

It prompts that the VIN has write successfully,select “OK”

Then it prompts that the current chassis number,select “OK”

Processing,please wait…

Return to select clear fault memory,select “ok”

Please stop the engine and turn the ignition switch on select “ok”

It prompts that clear fault memory has completed

Select “Read Fault Code”

It prompts that no diagnostic trouble code.

Please set the ignition switch to off and log out

Done!

 

Mitsubishi 2009 B2206 Chassis Number Matching Video Guide:

auto

Recent Posts

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

1 day ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

4 days ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

1 week ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

2 weeks ago

How to Solve Fendt 800 Vario S4 wayline Running Slow

If the vehicle is oscillating on the wayline or catches up the wayline very slowly…

2 weeks ago

How to Adjust Cruise Control Release Linkage for Kubota L3901 Excavator?

This is instruction show you guide on how to adjust cruise control release linkage for…

3 weeks ago