ECU Chip Tuning

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout

 

Vehicles: Monza, Kadett and Ipanema, from 91 to 96.

 

More ECU PINOUT Components:

ECU Modules Repair Pinpout & Components

 

 

Main components

1 Injector drive;

2 16156085 – Fuel pump relay drive;

3 34993 – Stepper motor drive;

4 Delco 196 E – 16045980 – PF relay – Injection light – Flight computer – V2 fan;

5 Processor;

6 Delco 196 E – 16045980 – V1 Fan – Heating relay collector – Ascending light – A / C relay;

7 34992 – 5V regulator;

8 NTC;

9 Processor;

10 Cristal – Clock;

11 Eprom, 27C128

 

Technical specifications

Special features

. Multec 700 exchanges are all the same, the difference is only in the mencal (Calibration Memory).

. Drive Beak – Commercial – IRF 540 or IRFZ34N.

 

Common defects

Failure in the fan relay drive;

Bad contact at the injector secondary drive terminals and pump, causing failure when moving the ECU. Necessary to resold the terminals.

 

Note:

For the injector to pulse, it is necessary to jump the terminals D9 and D10. Doing this, passes the earthing of the D9 to D10, that is, for the injector to work is pin D10 must be grounded.

ECUs are the same, what changes is the month.

 

Injector drive – 3 pins

 

 

This component is a  NPN transistor, with ferrite on the coupling (firing). This washer aims to eliminate electromagnetic interference.

Note: Note that the trigger has a range of 10 volts.

Secondary drive – Injector – Fuel pump

 

Processor

 

Mencal

 

Regulator 5 volts – 34992 – 15 pins

 

Delco 169 E 1 and 2

Delco 169 E – 1 – PF Relay – Injection light – Computer board – V2 fan – 15 pins

 

In this component the input (trigger) is negative and its out (out) is also negative.

Delco 169 E – 2 – V1 fan – collector heater relay

 

 

Stepper motor drive – 34993 – 9 pins

 

Note: When the ignition is switched off, the ECU starts the engine step, that is, to test the drive just turn on and off the ignition. And test with the oscilloscope.

 

Pump relay drive and Injector drive

 

auto

Recent Posts

Caterpillar C9 Engine Injection Actuation Pressure Output Fault Solution

This instruction show you guide on how to solve Caterpillar C9 engine injection actuation pressure…

6 days ago

How to Remove HV Battery Cooling FAN for HINO Truck with J05E Engine

Here is the instruction show you guide on how to remove HV battery cooling fan…

1 week ago

Scania Truck ALarm System APS 00001C Control Unit Error

Here is the instruction show you guide on how to solve Scania truck alarm system…

2 weeks ago

Doosan Stage V Engine U02A2 Timeout Error of CAN-Receive-Frame A1DEFI Solution

This instruction show you guide on how to repair Doosan stage V engine U02A2 timeout…

2 weeks ago

How to Solve Doosan Stage V Engine P011E Coolant Temperature Plausibility Fault

Here is the instruction show you guide on how to repair Doosan stage v egnine…

3 weeks ago

How to Use JPRO Diagnostics Performance Check Low Temp ATD Detroit Engine

This instruction show you guide on how to use JPRO Diagnostic software to performance check…

3 weeks ago