New Holland T6030 Electro-Hydraulic Remote Valve Removal and Calibration

Here is an instruction show you guide on how to remove and calibrate primary hydraulic power system electro-hydraulic remote valve for New Holland T6030 tractor.

 

Related Contents:

CNH DPA5 Adatper

2024 CNH EST 9.10 9.2New Holland Diagnostic Software Free Download

New Holland Agricultural & Construction Parts+Service Manual Free Download

 

 

Procedures:

Removal:

1 Steam clean remote control valve assembly prior to removal.
Lower hydraulic links.
Remove covers on remote valve couplers.
Remove support for pneumatic trailer brake couplers (where fitted).

2 Disconnect harness from electronic draft control solenoids, remote valve solenoids (2) and pressure feed hose (1).
NOTE: Identify the remote valve connectors to facilitate correct re-installation

3Disconnect the lift cylinder hydraulic hoses from the EDC slice (1)

4Using suitable lifting equipment support remote valve assembly, remove the three base securing bolts and lift valve stack from tractor

 

Calibration:

NOTE: The calibration procedure is controlled by the electronic management system. To prevent inadvertent movement of the tractor, park the tractor away from any obstacles, firmly apply the parking brake and block the wheels,
front and rear. Check that the Ground speed display is Zero before commencing.
1 Install the diagnostic connector 380000843 into the diagnostic socket (1)

2 Disconnect all implements from the rear remotes.
3 Make sure all EHR program switches are in the OFF position.
4 Use the “h”, “m” and “dimming” keys on the instrument cluster to navigate the HH menu’s to H1 and the rear EHR symbol on the RK controller.
The lower central display will show “CAL”

5 Depress the program switch for lever No.1 three times.
BAIL06CCM627AVA 3

6The calibration will proceed, the program lamp for EHR 1 will be illuminated and the lower central display will show “1”.
When the neutral position has been acquired and stored, the program lamp is turned off and the lower central display will show “2”

7 While 2 is displayed move the lever to the raise position, the program light will illuminate.
When movement is detected the program lamp for
EHR 1 is turned off. After the raise position is established the lower central display will change to 3, the program light will switch off

8 While 3 is displayed move the lever to the full flow lower position, the program light will illuminate.
When a stable value for the full flow lower position of the lever is seen it is recorded with the minimum flow rate value, the lower central display will change to 4, the program light will switch off

9While 4 is displayed move the lever to the float position, the program light will illuminate.
When a stable value for the float position of the lever is seen and recorded the lower central display will change to “CAL” to indicate the calibration procedure is complete

10To calibrate the remaining EHR levers (2 to 4), repeat the steps 5 to 9.
11Key OFF to store the calibration values.
NOTE: If a lever is not calibrated the program lamp is switched on regardless of the program switch state

More topics for New Holland repair,pls refer to:New Holland Trouble Repair

auto

Recent Posts

Volvo and Mack EPA 10 Engine Hydrocarbon Dosing Control Valve Test by JPRO

This instruction show you guide on how to perform hydrocarbon dosing control valve test for…

3 days ago

Fendt Tractor SPN 100 FMI 31 Oil Pressure Sensor Defect Solution

This instruction show you guide on how to solve Fendt tractor SPN 100 FMI 31…

4 days ago

Detroit GHG17 Heavy Duty Engine Piston Protrusion Measurement Procedure

Detroit GHG17 Heavy Duty Engine Piston Protrusion Measurement Procedure   Related Contents: 2024.06 Detroit Diesel…

6 days ago

Perkins 800 Series Engine Water Temperature Regulator Housing Remove and Install

This instruction show you guide on how to remove and install water temperature regulator housing.…

1 week ago

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout

Monza, Kadett and Ipanema Multec 700 GM ECU Components Pinout   Vehicles: Monza, Kadett and…

1 week ago

How to Remove Oil Pressure Regulation Valve for CLAAS AXION 950

This illustration show you guide on how to remove oil pressure regulation valve for CLAAS…

1 week ago