Categories: Auto Key Program

Nissan Consult 3 Plus Program Keyless Remote (T31/C11/K12)

This article show a guide on how to use Nissan Consult 3 Plus to program keyless remote (T31/C11/K12).Hope it helps,and if you want to know more about Nissan Consult 3 Plus,check:Nissan Consult 3 Plus Projects.

 

Related Contents:

Nissan Consult 3 Plus Software Download

How to Install Nissan Consult 3 III Plus Diagnostic Software

Nissan Consult 3 Plus Clone Interface

 

Procedures:

1.From the CONSULT-III plus “All DTC” screen, select the “BCM”.

2.Select “MULTI REMOTE ENTRY”.

3.Select “Work Support”.

4.When the next screen appears, (section shown below) select “REMO CONT ID REGIST” function to program the remotes.

 

 

ID Code Entry Procedure

STEP 1

Close all doors (Observe the operation of the interior light with each door to ensure the door switches are OK).

STEP 2

Operate lock using the driver side door lock and unlock switch (on P/Window swassy.)

 

STEP 3

1.Remove and insert the key into the ignition key 6 times within 10 seconds (turning the key barrel switch from OFF to ON counts as 1 time).

2.Hazard warning lamp blinks and all door unlocks.

NOTE:On the sixth key insertion, keep the key in the cylinder with the key barrel switch ON.Does the hazard lamp blink and all doors unlock?YES >> GO TO STEP 4.NO >> GO TO STEP 1.

 

STEP 4

Within 3 seconds after the hazard lamp blinks and all door unlocks, turn ignition switch to the ACC position and operate lock using the driver side door lock and unlock switch.

 

STEP 5

1.Press the lock or unlock button of the keyfobto be added.

2.All doors unlock simultaneously.

3.Hazard warning lamp blinks and all door unlocks.

4.Key ID is registered.

Is key ID registered?

YES-1 >> When adding a keyfob: GO TO STEP 6.

YES-2 >> When ending registration: GO TO STEP 8.

NO >> GO TO STEP 1.

 

STEP 6

Operate lock using the driver side door lock and unlock switch.

 

STEP 7

1.Press the lock or unlock button of the keyfobto be added.

2.All doors unlock simultaneously.

3.Hazard warning lamp blinks and all door unlocks.

4.Key ID is registered.

Is key ID registered?

YES-1 >> When adding a keyfob: GO TO STEP 6.

YES-2 >> When ending registration: GO TO STEP 8.

NO >> GO TO STEP 6.

 

STEP 8

Open the all doors >> REGISTRATION END.

 

auto

Recent Posts

Hitachi EX5600-7B Folding Stairway and Surrounding Parts Removal Guide

This instruction show you guide on how to remove folding stairway and surrounding part for…

1 day ago

Jungheinrich Junior AME13 Spring-Loaded Brake Electrical Connection Removal Guide

It is necessary step to remove electrical connection cable before you do disassemble or some…

3 days ago

How to Use Nexiq eTechnician Function Test?

Nexiq eTechnician provides a number of special tests to assist you with your vehicle diagnostic…

5 days ago

JCB JS140 Excavator P0523-68 Engine Oil Pressure Low Solution

Here car-auto-repair.com show you guide on how to repair JCB JS140 excavator P0523-68 trouble code…

6 days ago

Volvo Version 3 and 4 Truck Oil Pressure Test by Volvo Techtool

Here is the instruction show you guide on how to use Volvo TECHTOOL and VOCOM adapter to…

1 week ago

How to Solve Allison 3000 & 4000 Gen5 P071A Neutral at Stop Input Failed ON

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 transmission…

1 week ago