PCC1302 Power Engine Fault Code 119 Fuel Pressure Sensor OOR Low Solution

Here is a step by step guide on how to solve PCC1302 Power engine fuel pressure sensor OOR low solution fault code 119.

 

Related Contents:

2023 InPower V14.5 Pro V12 Diagnostic Software Free Download

PowerCommand Diagnostic 9 Pin Adapter Cable for InPower

 

 

Logic:
Fuel pressure sensor signal is out of range – shorted high.

Possible Causes:
1Faulty fuel pressure sensor connections
2Faulty fuel pressure sensor
3Faulty engine harness
4Faulty extension harness
5Verify the calibrations in the ECM and the PowerCommand controls

Diagnosis and Repair:
1.Faulty fuel pressure sensor connections
a.Inspect the fuel pressure sensor and the engine harness connector pins.
a.Disconnect the engine harness connector from the fuel pressure sensor.

b.Inspect for corroded pins, bent or broken pins, pushed back or expanded pins.
c.Inspect for evidence of moisture in or on the connector.
d.Inspect for missing or damaged connector seals.
e.Inspect for dirt or debris in or on the connector pins.

2Faulty fuel pressure sensor
aActive Sensor.
aCheck the fuel pressure sensor supply voltage.
aDisconnect the engine harness connector from the fuel pressure sensor.
bInstall the pressure sensor breakout cable between the sensor and the sensor harness connector.
cMeasure the supply voltage by connecting the breakout cable’s supply and return connectors to the multimeter. If the reading is between 4.75 and 5.25 VDC, then the supply voltage is correct.
bCheck the fuel pressure sensor signal (sense) voltage.
aDisconnect the engine harness connector from the fuel pressure sensor
bInstall the pressure sensor breakout cable between the sensor and the sensor harness connector.
cMeasure the signal voltage by connecting the breakout cable’s signal and return connectors to the multimeter. If the reading is between 0.46 and 4.56 V, then the signal voltage is correct. If not, sensor is faulty.

3.Faulty engine harness
a.Inspect the engine harness and the connector pins.
a.Disconnect the engine harness connector from the extension harness.
b.Inspect for corroded pins, bent or broken pins, pushed back or expanded pins.
c.Inspect for evidence of moisture in or on the connector.
d.Inspect for missing or damaged connector seals.
e.Inspect for dirt or debris in or on the connector pin.

b.Check for a short circuit from pin to pin.
a.Disconnect the engine harness from the extension harness.
b.Disconnect the engine harness connector from the fuel pressure sensor.
c.Disconnect the engine harness from all sensors that have a shared supply or return with the fuel pressure sensor.
d.Measure the resistance from the fuel pressure 5 VDC supply pin on the engine harness inline connector to all other pins in the engine harness inline connector.
e.Measure the resistance from the fuel pressure return pin on the engine harness inline connector to all other pins in the engine harness inline connector.
f.Measure the resistance from the fuel pressure signal pin on the engine harness inline connector to all other pins in the engine harness inline connector.
g.If all measurements are greater than 100k ohms, then the resistance is correct.

 

c.Check for a short circuit to engine block ground.
a.Disconnect the extension harness from the control.
b.Disconnect the extension harness from the engine harness.
c.Measure the resistance from the fuel pressure signal pin on the extension harness connector to the engine block ground.
d.Measure the resistance from the fuel pressure 5 VDC pin on the extension harness connector to the engine block ground.
e.If the measurement is more than 100k ohms, then the resistance is correct.
d.Check for an open circuit.
a.Disconnect the engine harness from the extension harness.
b.Disconnect the engine harness connector from the fuel pressure sensor.
c.Measure the resistance from the fuel pressure return pin on the engine harness inline connector to the fuel pressure return pin on the engine harness sensor connector.
d.If the measurement is less than 10 ohms, then the resistance is correct.

4.Faulty extension harness
a.Inspect the extension harness and the control connector pins.
a.Disconnect the extension harness connector from the control.
b.Inspect for corroded pins, bent or broken pins, pushed back or expanded pins.
c.Inspect for evidence of moisture in or on the connector.
d.Inspect for missing or damaged connector seals.
e.inspect for dirt or debris in or on the connector pins.

b.Check for a short circuit from pin to pin.
a.Disconnect the extension harness connector from the control.
b.Disconnect the extension harness from the engine harness.
c.Measure the resistance from the fuel pressure 5 VDC supply pin on the extension harness connector to all other pins in the extension harness connector.
d.Measure the resistance from the fuel pressure return pin on the extension harness connector to all other pins in the extension harness connector.
e.Measure the resistance from the fuel pressure signal pin on the extension harness connector to all other pins in the extension harness connector.
f.If all measurements are greater than 100k ohms, then the resistance is correct.

c.Check for a short circuit to engine block ground
a.Disconnect the extension harness from the control.
b.Disconnect the extension harness from the engine harness.
c.Measure the resistance from the fuel pressure signal pin on the extension harness connector to the engine block ground.

d.Measure the resistance from the fuel pressure 5 VDC pin on the extension harness connector to the engine block ground.
e.If the measurement is more than 100K ohms, then the resistance is correct.
d.Check for an open circuit.
a.Disconnect the extension harness connector from the control.
b.Disconnect the extension harness from the engine harness.
c.Measure the resistance from the fuel pressure return pin on the extension harness connector to the fuel pressure return pin on the extension harness inline connection.
d.If the measurement is less than 10 ohms, then the resistance is correct.

5.Verify the calibrations in the ECM and the PowerCommand controls
a.Using the display or the InPower Service tool, verify the calibration in the PCC.
a.If the calibration in the PCC matches the latest calibration on the InCal website,then the calibration is correct. If it does not, update the calibration to the latest.
b.Using the InSite Service tool, verify the calibration in the ECM.
a.If the calibration in the ECM matches the latest calibration on QSOL, then the calibration is correct. If it does not, update the ECM to the latest calibration.

auto

Recent Posts

Caterpillar C9 00 246-11 247-11 Brake Pedal Switch Fault Solution

Here is the instruction show you guide on how to solve Caterpillar C9 00 246-11…

17 hours ago

How to Solve Allison 3000 & 4000 Gen5 Engine Trouble Code P0703

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 engine…

4 days ago

How to Solve Fendt MT1149 Tractor SCR System Emptying Not Completed

Here is the illustration show you guide on how to solve Fendt MT1149 tractor SCR…

1 week ago

How to Set Play Between Timing Pinion Teeth for CLAAS AXION 920 Tractor?

Here is the instruction show you guide on how to set play between timing pinion…

2 weeks ago

Perkins 1106D Generation Injector Data Incorrect Test Guide

Perkins 1106D Generation Injector Data Incorrect Test Guide   Preparations: Perkins EST 2024A & 2023A…

2 weeks ago

How to Solve Deutz EMR3 Engine Error 16/108/APSCD Trouble

This instruction show you guide on how to solve Deutz EMR3 engine error 16/108/APSCD trouble…

2 weeks ago