Categories: Auto Repair

Porsche Cayenne 2011 EPB Programming after Replacement by Launch X431

In this instruction,i will show you how to use Launch X431 to calibrate EPB for Porsche Cayenne 2011- after replacement. This function allows you to maintain the electronic parking brake system safely and efficiently. Main functions include: Put the handbrake pad to the installation position, check the basic setting of the parking brake (check the gap of the handbrake pad), handbrake pad run-in and calibration.

For more repair case about Porsche,please refer to:Porsche Cayenne Repair Cases.

 

Cautions:

The replacement of Porsche Cayenne rear brake pads is the same as the replacement of ordinary brake pads. If you accidentally clicked on the menu of put handbrake pad to installation position, you must strictly follow the maintenance index to restore the electronic handbrake. After the replacement of handbrake pad, check the basic setting of the parking brake. Check the gap of the handbrake pad (standard gap is 1.9mm-2.4mm). Continue if this is OK. After the replacement of handbrake pad, the running-in function must be performed before the calibration.

 

Porsche Cayenne EPB Calibration:

1.Select Porsche Version V21.51 or above.

2.Select manual selection ->Cayenne(as of 2011) -> system selection ->parking brake ->special function

3.Click maintenance index, read the index information.

4.When replace the handbrake pad, select the function “Put hand brake pad to installation position”. After carrying out the function successfully as prompted, replace the brake pad. After the installation of new handbrake pad, select the function “Check basic setting of parking brake”

5.Click “OK” button, the actuator will complete a process of tension and release

6.Click “Next” to check the gap of the handbrake pad, see Picture 5.Note, the standard gap of Cayenne (as of 2011) is 1.9mm-2.4mm. If out of this range, please adjust it manually.

7.Click “Next” to complete the function “Check basic setting of parking brake”

8.After adjusting the gap, select “running-in” to run in the steel handbrake pad

9.After the replacement of handbrake pad, running-in must be performed! This function equals to adaptive learning. The instrument panel will prompt “Parking system enters maintenance mode”. This function requires one person to drive and another person to operate the software. It also has strict requirement to the site. Please be well prepared. Calibration should be performed only after the completion of 8 times of successful running-in,

10.Select “Calibration”

11.After satisfying the calibration conditions, click OK to perform the “Calibration” of the parking brake. When it prompts the calibration is complete, the software operation of replacing the handbrake pad is complete

More test report about Launch X431 please check:Launch X431 Test report

auto

Recent Posts

QSK60 CM2358 Engine Camshaft Speed/Position Sensor Data Erratic Incorrect

This illustration show you guide on how to repair Cummings QSK60 CM2358 engine camshaft speed/position…

5 days ago

Fendt MT800E Tractor DEF Tank Temperature Does Not Change Solution

Here is the instruction show yo guide on how to solve Fendt MT800E tractor DEF…

1 week ago

HITACHI Construction 4JJ1 P0092 Fuel Pressure Regulator Control Circuit High

Here car-auto-repair.com show you guide on how to solve ISUZU construction 4JJ1 engine P0092 fuel…

1 week ago

How to Solve Perkins 1106D EPG Engine E398 Low Fuel Rail Pressure Error

Here is the illustration show you guide on how to solve Perkins 1106D electric power…

1 week ago

Deutz EMR3 Aassembly Inspection and Initialisation Test Guide

Here comes the instruction on how to use SerDia2010 to perform assembly inspection and initialization…

1 week ago

HITACHI ZX-5 Excavator No Load Max Differential Pressure Measurement Guide

This instruction show you guide on how to perform No load max differential pressure measurement…

2 weeks ago