Porsche New Key Programming by Autel IM608 Pro EEPROM Function

EEPROM is hard to navigate,there are two scenarios for using EEPROM,one is if you want to add a new key using certain vehicles like BMW,Audi and Porsche,another is if you replace an ECU like the engine and need to read the old unit’s information.This instruction show you guide on how to use Autel IM608 Pro EEPROM programming function to add new key for Porsche.For more repair case about Porsche,please refer to:Porsche Cayenne Repair Cases.

 

What you need in this case?
Autel MaxiIM IM608 PRO Auto Key Programmer

 

Procedures:

Remove chipset from Porsche immobilizer system.

Power Autel IM608 Pro and access menu to select “Programmer”

Select “Chip (EEPROM,MCU,ECU)”–>”Chip read & write”–>”Immobilizer”

 

Select “BCM>5M48H>R(Back up)”

Select “D-Flash”–>”Schematic diagram”

Now zoom in on the schematic diagram and study it closely to find the correct places to connect the wires.

Operation guide:

1.In the first function execution,be sure to perform the BCM>5M48H>R(Backup) menu function

2.In the first function execution,be sure to read the D-Flash and P-FLASH data and back it up.

3.If the data backup fails,attempts to read with other menus are not allowed,otherwise data loss will be caused.

After removing the component from the vehicle,follow the steps below:

Step1:Important!

APA106 wire harness is only available for XP401/XP400 programmer;APA109 wire harness is only available for XP401 Pro/XP400 Pro programmer.

Step2:Check the circuit board of the current components,and identify the corresponding circuit board fro the pictures below.

Step3:Cut off the T1 wire,and remove the T2 and T3 components.

Step4:Wire harness extensions are forbidden.Ensure that there is no poor welding.Clear away welding stains with water for PCB cleaning.

Step5:Connect according to the connection method in the picture and read the data.

Step6:Upon completion of these operations,use a short wire to connect the T1 wire that was cut off to ensure that there is no disconnection;and weld the T2 and T3 components back.

 

Once the wire are connected,go back and select “Read”

After reading finish,just input file name to save it on Autel IM608 Pro tablet

Back to home screen to select “IMMO”

Then select “Porsche”–>”Expert Mode”–>”New Porsche”–>”Load EEPROM data”

Then select your Porsche BCM type “5M48H”

Select the D-Flash file saved just now

After D-Flash data loading,i will show the vehicle immobilizer information

Notice:Recommend you take a picture of this information

Put the blank key in the XP400 programmer

Click “Make dealer Key” and click “Yes” to continue

Make dealer key finished

Once make dealer key is successful,then you can move on to key learning

You will need to connect your Jvci in to the obd2 port for this last step

 

More Autel devices real feedbacks,please refer to:Autel Devices Feedback

auto

Recent Posts

How to Remove Second Tank for CLAAS AXION 960-920 Tractor

This instruction show you guide on how to remove second tank for CLAAS AXION 960-920…

18 hours ago

Doosan Excavator P0408 Maximum EGR Rate Governor Deviation Error Solution

This instruction show you guide on how to solve Doosan excavator P0408 maximum EGR rate…

4 days ago

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

6 days ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

1 week ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

2 weeks ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

3 weeks ago