Categories: Auto Repair

Tesla Model 3 Airbag Crash Data Reset by Launch X431

This instruction show you guide on how to reset airbag crash data for Tesla Model 3 by Launch X431.

 

This function is used to reset airbag crash data in order to recycle airbag ECU (Electric Control Unit). (In some countries, erasing airbag crash data without changing airbag assembly is not legal. So, we highly recommend to replacing car’s entire airbag assembly).

 

Preparations:

Launch X431 V Pro or Launch X431 PAD V (Amazon Official Shop)

 

Procedures:

Preparation (For some Model 3 vehicle, there’s no need to remove airbag ECU. If OBDII can communicate normally, please skip this procedure)

Remove airbag ECU from vehicle

Airbag ECU connection position

Airbag ECU wiring diagram

Wiring and pin allocation

+12V: 12V power supply

GND: Ground wire

CAN_H: CAN high

CAN_L: CAN low

Tesla airbag repair designated connector wiring diagram

 

Resetting airbag crash data software operation procedure

Go into Tesla software, select”Model 3″ ->”Special Function” -> “Service AIRBAG” ,as shown in figure 1, or select”Model 3″ -> “System Selection” –> “SDM Airbag” -> “Special Function”

 

Unlock airbag ECU, click” Unlock EEPROM After Crash” . It will finish automatically.

Read airbag ECU memory, select “Read EEProm” menu, when reading is done, input backup file name, select backup file storage directory, data backup is done.

Input backup file name, for example “Model_3_20210520”

Click “OK”to backup data.

Read EEPROM and backup finished

Erase crash data, go into ” Erase Crash -Direct” menu, select ” Read EEProm”  backup file. The software will automatically perform ” Write EEProm”  to write backup data and verify if data written is correct.

Select backup file

Click “Model_3_20210520.bin” to select back file

Edit backup data. Press” YES”  to use default data. Press ” Auto Set”  to automatically modify value (recommended). Press ” Memory Dump”  to manually modify backup data.

if you press ” Auto Set” , it will skip this procedure. Press ” Memory Dump” , you can manually modify backup data. Start address is where the system starts to read backup data and it can be modified manually. After entering start address, press ” Confirm”  to write modified data, click ” Restore”  to recover it to old value.

Write data, erase airbag crash data.

 

Verify written data

Write crash data, go into “Write EEProm” menu, select backup file. The software will automatically write backup data and verify if data is correct. This procedure is similar to above mentioned procedure “Erase Crash -Direct” .

Select backup file

Click “Model_3_20210520.bin” to select back file

Edit backup data. Press“YES”to use default data. Press “Auto Set” to automatically modify value (recommended). Press “Memory Dump” to manually modify backup data.

Write Data

Verify written backup data

Erase crash record, go into”Erase Crash Record” menu, the software will automatically finish it.

Clear DTC (Diagnostic Trouble Code), put airbag ECU back. Erasing crash data is done.

If you find the above procedure is cumbersome, please click ” Crash Data Resetting Automatically”  menu, it will automatically perform all procedures.

More test report about Launch X431 please check:Launch X431 Test report

auto

Recent Posts

Doosan Excavator P0408 Maximum EGR Rate Governor Deviation Error Solution

This instruction show you guide on how to solve Doosan excavator P0408 maximum EGR rate…

1 day ago

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

3 days ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

6 days ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

1 week ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

2 weeks ago

How to Solve Fendt 800 Vario S4 wayline Running Slow

If the vehicle is oscillating on the wayline or catches up the wayline very slowly…

3 weeks ago