Categories: Auto Repair

Tesla Model S Airbag Crash Data Reset by Launch X431

This instruction show you guide on how to use Launch X431 device to reset airbag crash data for Tesla model S.The function is used to reset airbag crash data in order to recycle airbag ECU (Electric Control Unit).

Note:In some countries, erasing airbag crash data without changing airbag assembly is not legal. So,we highly recommend to replacing car’s entire airbag assembly.

 

Related Device:

Launch X431 V Pro or Launch X431 PAD V (Amazon Official Shop)

Android diagnostic devices, Tesla airbag repair designated connector

TESLA V10.02 or above version

 

Airbag ECU connection position

Airbag ECU wiring diagram

PW: Power wiring, wire two position to write EEPROM.

+12V: 12V power supply

GND: Ground wire

CAN_H: CAN high

CAN_L: CAN low

 

Tesla airbag repair designated connector wiring diagram

 

 

Resetting airbag crash data software operation procedure

Go into Tesla software, select Model S->Special Function->Service AIRBAG,as shown in figure 1, or select Model S-> System Selection–> SDM Airbag-> Special Function, as shown in figure 2, it will display the following menu.

 

Read airbag ECU memory, select Read EEPROM menu, when reading is done, input backup file name, select backup file storage directory, data backup is done.

Input backup file name, for example “Model_s_20210520”

Click “OK”to backup data.

 

Read EEPROM and backup finished

Erase crash record, go into Erase Crash Record menu, the software will run for several seconds and will automatically finish it.

Re-write airbag ECU battery backup data, select “Write EEProm” menu.

Select backup file

Click “Model_s_20210520.bin” to select back file

Click “OK”button

Edit backup data. Press [YES] to use default data. Press [Auto Set] to automatically modify value (recommended). Press [Memory Dump] to manually modify backup data.

If you press [Auto Set], it will skip this procedure. Press [Memory Dump], you can manually modify backup data. Start address is where the system starts to read backup data and it can be modified manually. After entering start address, press [Confirm] to write modified data, click [Restore] to recover it to old value.

 

Write Data

 

Perform “Clear Fault Code” function, and then put airbag ECU back on vehicle.

If you find the above procedure is cumbersome, please click [Crash Data Resetting Automatically] menu, it will automatically perform all procedures.

More test report about Launch X431 please check:Launch X431 Test report

auto

Recent Posts

How to Solve Allison 3000 & 4000 Gen5 Engine Trouble Code P0703

This instruction show you guide on how to solve Allison 3000 & 4000 Gen5 engine…

2 days ago

How to Solve Fendt MT1149 Tractor SCR System Emptying Not Completed

Here is the illustration show you guide on how to solve Fendt MT1149 tractor SCR…

1 week ago

How to Set Play Between Timing Pinion Teeth for CLAAS AXION 920 Tractor?

Here is the instruction show you guide on how to set play between timing pinion…

1 week ago

Perkins 1106D Generation Injector Data Incorrect Test Guide

Perkins 1106D Generation Injector Data Incorrect Test Guide   Preparations: Perkins EST 2024A & 2023A…

1 week ago

How to Solve Deutz EMR3 Engine Error 16/108/APSCD Trouble

This instruction show you guide on how to solve Deutz EMR3 engine error 16/108/APSCD trouble…

1 week ago

Kubota L4701 High Pressure Relief Valve Pressure Checking

Here show guide on how to check high pressure relief valve pressure for Kubota L4701…

2 weeks ago