What is Toyota 4D Key Tool?

Toyota 4D Key Tool is a immobilizer off software special for Toyota.You can use it to repair immobilizer and synchronization with motor ECU utility.

Toyota 4D Key Tool Installation OS Requirements:

OS: Windows XP/7/8/10

Minimum Specifications:

Processor : Intel Core 2 Duo 1.8Ghz or ADM Athlon X2 2.4 Ghz

RAM :2 GB

HDD : 160GB

 

Toyota 4D Key Tool v1.2 Free Download:

https://mega.nz/#!T1EjGT5D!hDFcjgE2D9sAvGBjVbX3orJVdS6NApmCuFCdL9FEVvs

 

And for more immo off software please check here:IMMO OFF Software Download

How to Use Toyota 4D Key Tool

Is no car transponder key:

Remove immo (Transponder ID ECU) from car. Open it and read EEPROM. Open immo dump with “TOYOTA 4D KEY TOOL” and push “Generate keys”. Now using any transponder tool (Codereader, ZedBull, RW4 or other) write transponder data to TPX3 or EH (electronic 4D emulator). This transponder will be car Master (Black) key.

 

Car not start – unknown problem:

First make car immobilizer and motor ECU diagnostic. If Immobilizer have error code “wrong transponder” or “transponder ID is not registered” – generate new transponder from immobilizer dump. If is no fault codes in immobilizer and in motor ECU is fault code “immobilizer fault B2799” – you need synchronize immo-motor ECU.

 

Toyota 4D Key Tool Support Car List:

Avensis 2003:

Location of the immobox is just in the middle of the dash very deep towards the wind  screen.IMMOBOX : 89780-05030,  EEPROM : 24C04

Aygo 2005:

Location of the immobox is behind the dashboard. IMMOBOX : 89780 – 0H011, EEPROM : 24C04

Corolla 2005:

The control circuit of the engine immobiliser system has been integrated into the engine ECU.The engine ECU is mounted behind the passenger side glove box.Some times  immobiliser system has immo box. Inside is 93C66 eeprom

Hilux 2006:

Immo location : Behind the noise insulation coat. Inside is 93C66 eeprom

Prius 2005:

Location of immobox is behind steering wheel. IMMOBOX : 89780-0F010, EEPROM : 93LC66B

Rav4 2004:

The immo box is mounted in the lower instrument panel. Inside is 93C66 eeprom.

Yaris 2003:

The  immo box is mounted in the upper centre of instrument panel. Inside is 93C56 or 93C66 eeprom

 

Motor ECU sychronization:

All Toyota Lexus with OBDII connector engine ECU registration procedure

Engine ECU Replacement:

When the Engine ECU is replaced,ECU communication must be completed.ECU communication must be performed between the transponder ECU and the Engine ECU.Complete ECU communication using the following steps:

A.Insert a registered Master Key into the ignition cylinder.

B.Turn the ignition ON (engine OFF)

C.Short Tc  and CG terminals of DLC 3 using Diagnosis Check Wire (SST 09843-18020 or equivalent) and leave for 30 minutes.

D.After 30 minutes,turn ignition OFF and remove check wire from DLC3

E.Start the vehicle to confirm successful ECU communication

Note:If ECU communication is not completed correctly,the engine will not start and DTC b2799 will be set.DTC B2799 will be cleared after the engine starts correctly

auto

Recent Posts

How to Calibrate 2403 Steering Valve for Fendt 800 S4 Tractor

Here is the instruction show you guide on how to calibrate 2403 steering valve for…

1 day ago

Massey Ferguson Tractor Electrohydraulic Spool Valves Configuration

This function requires all connectors to be disconnected from all electrohydraulic valves on the tractor.You…

4 days ago

How to Remove Center Joint and Center Frame for HITACHI Hitachi EX5600-7B

This instruction show you guide on how to remove center joint and center frame for…

7 days ago

How to Repair Doosan Machine P0100 DTC Signal Error

How to solve Doosan heavy duty machine P0100 fault code signal error of air mass…

2 weeks ago

How to Solve Fendt 800 Vario S4 wayline Running Slow

If the vehicle is oscillating on the wayline or catches up the wayline very slowly…

2 weeks ago

How to Adjust Cruise Control Release Linkage for Kubota L3901 Excavator?

This is instruction show you guide on how to adjust cruise control release linkage for…

3 weeks ago